1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Truerobotech
    Post

    Solved Will Not Extrude When Temp Is 185

    @danzca6 Awesome thanks for that I will stash that knowledge for future!
    Post by: Truerobotech, Oct 22, 2016 in forum: Troubleshooting
  2. Truerobotech
    Post

    Solved Will Not Extrude When Temp Is 185

    Marking this one solved by changing the "#define EXTRUDE_MINTEMP 185" line to 175 and uploading the firmware I can print just fine at a lower...
    Post by: Truerobotech, Oct 21, 2016 in forum: Troubleshooting
  3. Truerobotech
    Post

    Solved Will Not Extrude When Temp Is 185

    Here is the line in the firmware, I could find any others. Ill be testing this evening so will update is successful. #define EXTRUDE_MINTEMP 175...
    Post by: Truerobotech, Oct 21, 2016 in forum: Troubleshooting
  4. Truerobotech
    Post

    Solved Will Not Extrude When Temp Is 185

    Thanks Geof, figured it might be firmware but didnt want to have to dive in there unless I was sure. Now I just have to remember the last one I...
    Post by: Truerobotech, Oct 21, 2016 in forum: Troubleshooting
  5. Truerobotech
    Post

    Solved Will Not Extrude When Temp Is 185

    Yep 190 pretty low and pushing it but even the manuf RigidInk recommends 180 - 210. All the benchys I have tested thus far are screaming to be...
    Post by: Truerobotech, Oct 21, 2016 in forum: Troubleshooting
  6. Truerobotech
    Thread

    Solved Will Not Extrude When Temp Is 185

    Hello forums its been some time since a post, I still lurk and try to find an opportunity to contribute though. I looked and searched and found...
    Thread by: Truerobotech, Oct 21, 2016, 9 replies, in forum: Troubleshooting
  7. Truerobotech
    Post

    Solved printing in the air!

    Glad you were able to solve it! Good on you @Ocsff for the suggestion!
    Post by: Truerobotech, Mar 21, 2016 in forum: Troubleshooting
  8. Truerobotech
    Post

    Solved printing in the air!

    Hope the re-adding of the machine works! I suspect something in your G Code based on the z numbers in there but im no G code expert :). I have...
    Post by: Truerobotech, Mar 20, 2016 in forum: Troubleshooting
  9. Truerobotech
    Post

    Solved printing in the air!

    You mention custom G-Code, can you post that specific G Code and pics of your Matter Control Settings you tried? I could just be a visual person...
    Post by: Truerobotech, Mar 19, 2016 in forum: Troubleshooting
  10. Truerobotech
    Post

    Solved Y axis jumps, sticks, screws up 90% of prints.

    Thanks @Kevin Robo 3D I do not have the cable ribbon on my bed its all under the bed ( I am going to change to it down the road.) Ahh bummer...
    Post by: Truerobotech, Mar 18, 2016 in forum: Troubleshooting
  11. Truerobotech
    Post

    Solved Y axis jumps, sticks, screws up 90% of prints.

    I have had similar problems mine were caused by the heated bed wire hanging up on the gears during a print. Maybe your issue? I end up lifting...
    Post by: Truerobotech, Mar 18, 2016 in forum: Troubleshooting
  12. Truerobotech
    Post

    Solved printing in the air!

    Can you clarify the issue a bit more? Whats occurs when? i.e. You send the print from matter control, it runs the 9 point check, then heads to the...
    Post by: Truerobotech, Mar 18, 2016 in forum: Troubleshooting
  13. Truerobotech
    Post

    Solved Abs learning & Troubleshooting

    Thanks @Mike Kelly and @mark tomlinson sorry for the delayed reply I was able to get over here and see your post (plus like them). I had a...
    Post by: Truerobotech, Feb 17, 2016 in forum: Troubleshooting
  14. Truerobotech
    Thread

    Solved Abs learning & Troubleshooting

    [IMG] This image is of the sme print white is PLA and the Red is ABS. The tabs on the abs snapped with little pressure the white pla has flexed...
    Thread by: Truerobotech, Feb 4, 2016, 3 replies, in forum: Troubleshooting
Showing results 1 to 14 of 14
Search Again