1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    I am running a Geckotek Heated bed. It uses the Original Robo3D PCB heating element. It was ran off 12v originally. The current RoboR1-R1+ come...
    Post by: Jim Leoanrd, Apr 12, 2018 in forum: Mods and Upgrades
  2. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    My setup just heats the Bed with 18v. The stock Power supply is retained for all other power. Mark, are you refering to just Extruder heaters or...
    Post by: Jim Leoanrd, Apr 12, 2018 in forum: Mods and Upgrades
  3. Jim Leoanrd
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I think I saw your post in the Robo3D facebook group. Looked to be working well. I would love to upgrade to MESH or UBL, but it prints so darn...
    Post by: Jim Leoanrd, Feb 21, 2018 in forum: Mods and Upgrades
  4. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    That would probably work very well. I have been printing with the same 5A fuse since it was set up, so over 5 months now without a single issue....
    Post by: Jim Leoanrd, Dec 11, 2017 in forum: Mods and Upgrades
  5. Jim Leoanrd
    Post

    Titan Areo Upgrade Prusa Style

    This looks like a clean solution. Did you get yours up and running?
    Post by: Jim Leoanrd, Jun 29, 2017 in forum: Mods and Upgrades
  6. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    My testing tonight had the following results: All at 123.2V Printer Powered on = 0.38A Printer Powered and Extruder Heating = 0.85A Printer...
    Post by: Jim Leoanrd, Jun 26, 2017 in forum: Mods and Upgrades
  7. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Got the 18v Power supply installed. Came out pretty clean. Only 2 visible screws from the front. Heats up from room temp to 100C+ in ~9 minutes....
    Post by: Jim Leoanrd, Jun 26, 2017 in forum: Mods and Upgrades
  8. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    18v power supply showed up. Ill get it installed in the next couple days. Even knowing the measurements, it was surprisingly small!...
    Post by: Jim Leoanrd, Jun 22, 2017 in forum: Mods and Upgrades
  9. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    That would be nice! most of my settings are pretty good, but Im constantly swapping between ABS and TPU, then throw in some PLA and Nylon. Im...
    Post by: Jim Leoanrd, Jun 20, 2017 in forum: Mods and Upgrades
  10. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    A little of both. I have a bad habit of preheating while setting up the print, then never actually sending it to the printer! Coming back later to...
    Post by: Jim Leoanrd, Jun 20, 2017 in forum: Mods and Upgrades
  11. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Thank you, and I do agree about the time being trivial, but sometimes Im running in and out, and having it sit warming up to check the first layer...
    Post by: Jim Leoanrd, Jun 20, 2017 in forum: Mods and Upgrades
  12. Jim Leoanrd
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    In your opinion is 1.1.1 from May 11 the most stable of the releases that support the mesh everyone loved so much? I only saw a 1.1.0 from may 3...
    Post by: Jim Leoanrd, Jun 20, 2017 in forum: Mods and Upgrades
  13. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    The heat sink capacity definitely keeps things consistent though! I may just order a Keenovo Heater, and use the big external adjustable unit I...
    Post by: Jim Leoanrd, Jun 20, 2017 in forum: Mods and Upgrades
  14. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Following up on my progress, I have some data on the Geckotek Bed replacement and power supply testing. With the stock Geckotek (original Robo3d...
    Post by: Jim Leoanrd, Jun 20, 2017 in forum: Mods and Upgrades
  15. Jim Leoanrd
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Any good reason to not use an 18v 20A power supply for the bed heater? It should still heat alot faster than 12v, but will require much less...
    Post by: Jim Leoanrd, Jun 14, 2017 in forum: Mods and Upgrades
  16. Jim Leoanrd
    Post

    Simplify 3d

    Ive been using Simplify3D for a couple weeks now, and finally put together a Post-Processing Script to be able to Pause and change filament. This...
    Post by: Jim Leoanrd, Nov 21, 2016 in forum: Software
Showing results 1 to 16 of 16
Search Again