1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. NKakon
    Thread

    wiring a new fan for the printer

    Hey all, I just finished printing and installing a dual fan mount with shrouds for the R1, and I'm now realizing I overlooked the slight detail...
    Thread by: NKakon, Jul 26, 2017, 2 replies, in forum: Mods and Upgrades
  2. NKakon
    Post

    Answered Print head clogged

    approximately how long should I expect it to take the plastic to melt out at that temp? just for an idea of knowing if it is or isnt working when...
    Post by: NKakon, Jun 10, 2017 in forum: Troubleshooting
  3. NKakon
    Post

    Answered Print head clogged

    Hooray possible solution! Thanks I'll try it out after the weekend
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  4. NKakon
    Post

    Answered Print head clogged

    Unfortunately no... it stayed stuck in both. I feel like I should be able to clear the plastic in the hot end itself now though For the heat...
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  5. NKakon
    Post

    Answered Print head clogged

    yeah, i managed to seperate the heat sink from the hot head and i pulled out the cartridge and thermistor so how i just have the metal parts for each
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  6. NKakon
    Post

    Answered Print head clogged

    That sounds terrifyingly risky, and much as I have access to those things, wouldnt it be easier to heat up the heat sink with a blowtorch and try...
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  7. NKakon
    Post

    Answered Print head clogged

    And just as a backup, could you post a link to a recommended hot end replacement?
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  8. NKakon
    Post

    Answered Print head clogged

    they got hot after a while in the end, i just wasnt able to heat up the heat sink enough to push the plastic out is there any chance this hot end...
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  9. NKakon
    Post

    Answered Print head clogged

    first thanks forthe amazingly fast reply! im currently trying to heat up the head and remove the plastic but the other end of the metal body...
    Post by: NKakon, Jun 9, 2017 in forum: Troubleshooting
  10. NKakon
    Thread

    Answered Print head clogged

    I tried running a print today and left it alone for 10 minutes. When I came back the printer wasnt extruding plastic anymore. I quickly stopped...
    Thread by: NKakon, Jun 9, 2017, 17 replies, in forum: Troubleshooting
  11. NKakon
    Thread

    Dual Extrusion on Robo 3D R1

    Hi, I've seen basically everyone on this forum advise against modifying to dual extrusion because it was a giant pain in the neck and ends up...
    Thread by: NKakon, Mar 5, 2017, 14 replies, in forum: General Questions
  12. NKakon
    Thread

    Unanswered MatterControl First layer quality

    So as far as I've been able to manage, I havent yet found the setting for creating a nice smooth first layer using the mattercontrol slicer as is...
    Thread by: NKakon, May 16, 2016, 3 replies, in forum: General Questions
  13. NKakon
    Thread

    Cura Extrusion Multiplier

    Does anyone know of a way to control the flow rate during a print? I've seen that there's a tweak at Z plugin and from what I've understood that's...
    Thread by: NKakon, May 16, 2016, 0 replies, in forum: General Questions
Showing results 1 to 13 of 13
Search Again