1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Michele Beyer
    Post

    Unanswered Abs settings

    I have also built a box/towel fort around the printer to keep the heat in :-) I can send pictures of that as well :-)
    Post by: Michele Beyer, Apr 1, 2017 in forum: Troubleshooting
  2. Michele Beyer
    Post

    Unanswered Abs settings

    Hello Andy, I've been printing with ABS, quite successfully, this weekend (I had an entire roll, and it's the color I needed!). I use Repetier...
    Post by: Michele Beyer, Apr 1, 2017 in forum: Troubleshooting
  3. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    Thank you for you help Mark!!
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  4. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    Oh, and I'm using Repetier :-)
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  5. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    This print is MUCH better! I think I may back off and try -0.9 as the first layer is looking a little flat, but otherwise, it's going great!
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  6. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    Ok, gotcha! I will test this out!
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  7. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    Ok, thank you so much. Also - you're saying I should add the z-offset to my g-code and not adjust it in the software? I attached an image on one...
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  8. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    And when I lowered to extrusion temperature to 185 it didn't print well either :-/ but I can play around with the z-offset and temperatures a bit...
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  9. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    So my G-code should read: G28 ; home all axes M565 Z-1.0 ; G29 ; G1 Z50 F5000 ; lift nozzle ?? :-) Also - I attached the current settings for...
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  10. Michele Beyer
    Post

    Solved Print is stringy on first layer - please help! :-)

    Images of my current settings........
    Post by: Michele Beyer, Mar 28, 2017 in forum: Troubleshooting
  11. Michele Beyer
    Thread

    Solved Print is stringy on first layer - please help! :-)

    Hey everybody! So, I'm finally back to having some fun with my printer and am having issues with my print. I have attempted to print this thing...
    Thread by: Michele Beyer, Mar 28, 2017, 15 replies, in forum: Troubleshooting
  12. Michele Beyer
    Post

    Unanswered First layer good, Second layer crap :-)

    Thank you Mark, I'm not sure why it was so low either (swear it was set to 0.2). But so far, I'm on layer 5 and no issues! :-)
    Post by: Michele Beyer, Jan 8, 2017 in forum: Troubleshooting
  13. Michele Beyer
    Post

    Unanswered First layer good, Second layer crap :-)

    I've attached an image with many of my settings, thought this may be helpful. I'm not, in any way, a software person and starting to think I need...
    Post by: Michele Beyer, Jan 8, 2017 in forum: Troubleshooting
  14. Michele Beyer
    Thread

    Unanswered First layer good, Second layer crap :-)

    I'm printing with ABS and finally got the first layer to stick, but the second layer is a mess! Current speed settings are attached in a photo as...
    Thread by: Michele Beyer, Jan 8, 2017, 4 replies, in forum: Troubleshooting
  15. Michele Beyer
    Post

    Partially Solved 2nd Layer not sticking to 1st layer (PLA).....

    I'm pretty sure it uploaded just fine, but I'm still having problems........
    Post by: Michele Beyer, Oct 13, 2016 in forum: Troubleshooting
  16. Michele Beyer
    Post

    Partially Solved 2nd Layer not sticking to 1st layer (PLA).....

    I guess my only other question would be, how do I know if I uploaded the firmware correctly? I assume there's a place I can check that, just not...
    Post by: Michele Beyer, Oct 13, 2016 in forum: Troubleshooting
  17. Michele Beyer
    Post

    Partially Solved 2nd Layer not sticking to 1st layer (PLA).....

    Wow, I'm really paying attention huh? ;-) And I just go through arduino for this right? Sorry, it's been a really long time since I've done...
    Post by: Michele Beyer, Oct 13, 2016 in forum: Troubleshooting
  18. Michele Beyer
    Post

    Partially Solved 2nd Layer not sticking to 1st layer (PLA).....

    I've got a folder that I saved back on 05/21/2016 entitled ROBO3DR1V3_06112015. The folder I just downloaded from the link you sent is...
    Post by: Michele Beyer, Oct 13, 2016 in forum: Troubleshooting
  19. Michele Beyer
    Post

    Partially Solved 2nd Layer not sticking to 1st layer (PLA).....

    I've got the R1+ model, unsure about the leadscrews, I use matter control, and I am not sure when I last updated the firmware. However, I don't...
    Post by: Michele Beyer, Oct 13, 2016 in forum: Troubleshooting
  20. Michele Beyer
    Thread

    Partially Solved 2nd Layer not sticking to 1st layer (PLA).....

    See photo - I keep adjusting my extruder temps and bed temps to no avail!
    Thread by: Michele Beyer, Oct 13, 2016, 16 replies, in forum: Troubleshooting
Showing results 1 to 20 of 32 Next >
Search Again
Page 1 of 2