1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Brendan Fennell
    Post

    Chewing Filament When Printing Benchy

    Sorry about the time between updates, I've been busy with school. When I changed only the filament, it had no effect on the print. My most recent...
    Post by: Brendan Fennell, Oct 6, 2016 in forum: Mods and Upgrades
  2. Brendan Fennell
    Post

    Chewing Filament When Printing Benchy

    So I started a test again with a different filament just in case, the purple has always felt different than my other rolls of PLA, soft instead of...
    Post by: Brendan Fennell, Sep 28, 2016 in forum: Mods and Upgrades
  3. Brendan Fennell
    Post

    Chewing Filament When Printing Benchy

    No dice. It made it a little farther, but still wasn't close to finished. (it may look significantly farther, but that's because I ripped off all...
    Post by: Brendan Fennell, Sep 27, 2016 in forum: Mods and Upgrades
  4. Brendan Fennell
    Post

    Chewing Filament When Printing Benchy

    Okay, cool. Thanks for the tips. I am using PLA, and I'm not using an oiler, but I've been printing for a while never needing one. I'm printing at...
    Post by: Brendan Fennell, Sep 27, 2016 in forum: Mods and Upgrades
  5. Brendan Fennell
    Thread

    Chewing Filament When Printing Benchy

    So I've been trying to dial in my e3d v6 with the .25mm nozzle, and I'm having a repeating problem. I'm trying to print Benchy, the little boat...
    Thread by: Brendan Fennell, Sep 27, 2016, 13 replies, in forum: Mods and Upgrades
  6. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    Most likely, 2.4L won't move much air!
    Post by: Brendan Fennell, Sep 27, 2016 in forum: Mods and Upgrades
  7. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    Nah, I'll bolt it to my tailpipe and rev the car at 6,000 rpm for the duration of the print
    Post by: Brendan Fennell, Sep 27, 2016 in forum: Mods and Upgrades
  8. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    Haha, that's true. I'm thinking of doing a big rebuild of the printer right around Christmas with octopi, a titan, thermocouple, etc. So I'll just...
    Post by: Brendan Fennell, Sep 25, 2016 in forum: Mods and Upgrades
  9. Brendan Fennell
    Post

    E3D Titan Extruder

    Okay, never mind. I found them on your Thingiverse profile. Thanks!
    Post by: Brendan Fennell, Sep 25, 2016 in forum: Mods and Upgrades
  10. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    So I've given up on the external cooling idea, at least for now. The printing and assembly went rather smoothly, but even the highest flow case...
    Post by: Brendan Fennell, Sep 25, 2016 in forum: Mods and Upgrades
  11. Brendan Fennell
    Post

    E3D Titan Extruder

    First of all, I want to say the designs you've put up in this thread are AWESOME!! I LOVED the way you built those plugs into the fan mounts,...
    Post by: Brendan Fennell, Sep 25, 2016 in forum: Mods and Upgrades
  12. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    So I lowered my Temps to 195, below that I start to have adhesion issues with the bed. If there's a way on matter control to easily make the first...
    Post by: Brendan Fennell, Sep 23, 2016 in forum: Mods and Upgrades
  13. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    Thanks so much! I'll adjust the temperature, try some more test prints, and report back!
    Post by: Brendan Fennell, Sep 21, 2016 in forum: Mods and Upgrades
  14. Brendan Fennell
    Post

    New Cooling System, V6 Volcano

    I'll try lowering my temps first, thanks! How do I know when I've reached an optimal temperature? I've always just printed PLA at 210C
    Post by: Brendan Fennell, Sep 21, 2016 in forum: Mods and Upgrades
  15. Brendan Fennell
    Thread

    New Cooling System, V6 Volcano

    So I recently installed my V6 Volcano hot end, and I'm loving the improved print speeds and strength. I've been using the 1.2mm nozzle. The thing...
    Thread by: Brendan Fennell, Sep 21, 2016, 15 replies, in forum: Mods and Upgrades
  16. Brendan Fennell
    Post

    Schlomo's Robo Beast Inspired Printer!

    That bridging's fantastic! I just got my E3D V6 upgrade finished today. Do you mind if i ask you what you did for your parts fan to get such good...
    Post by: Brendan Fennell, Mar 16, 2016 in forum: Show and Tell
Showing results 1 to 16 of 16
Search Again