1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    Removable more than 12 inches then :D Thanks for all the help
    Post by: theman00011, Jul 19, 2018 in forum: Troubleshooting
  2. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    What about a different material for the bed instead of glass? I haven't really looked into it but maybe one of those magnetic build platforms you...
    Post by: theman00011, Jul 18, 2018 in forum: Troubleshooting
  3. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    Yeah, I wouldn't go any higher than 0.2mm on the 0.25mm nozzle but 0.2mm isn't too bad. I wish I didn't have to change nozzles so often but my...
    Post by: theman00011, Jul 18, 2018 in forum: Troubleshooting
  4. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    No worries. I had mentioned in a previous post that I had retraction turned off so I knew retraction wasn't causing the filament to jam. The part...
    Post by: theman00011, Jul 17, 2018 in forum: Troubleshooting
  5. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    So I had a bit of better quality older PLA laying around so I decided to give it a try, and with that PLA at 20mm/s and 205C, it completed without...
    Post by: theman00011, Jul 16, 2018 in forum: Troubleshooting
  6. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    Hmm, alright. I am ordering some better quality PLA in case it is a problem with the filament itself. I also asked the Printedsolid guys if they...
    Post by: theman00011, Jul 16, 2018 in forum: Troubleshooting
  7. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    I had did a E step calibration right after installing the V6 on the 0.4mm nozzle, and I figured it would still be accurate but I did it again...
    Post by: theman00011, Jul 15, 2018 in forum: Troubleshooting
  8. theman00011
    Post

    Solved E3D V6 0.25mm nozzle clogging mid print

    To what speed would you recommend? Because that picture, the right side was done at 10mm/s, and I print normally 0.4mm nozzles at 40mm/s. I've...
    Post by: theman00011, Jul 14, 2018 in forum: Troubleshooting
  9. theman00011
    Thread

    Solved E3D V6 0.25mm nozzle clogging mid print

    Printer: R1+ Filament type: Black PLA Extruding Temp: 200-215 Bed Temp: 50 Bed makeup: Glass+Light glue stick for small prints Print speed:...
    Thread by: theman00011, Jul 13, 2018, 18 replies, in forum: Troubleshooting
  10. theman00011
    Post

    Worth upgrading to an E3D V6?

    Just finished putting it all together and cleaning it up. It wasn't too difficult, the cable management was definitely the hardest part. I decided...
    Post by: theman00011, Jul 11, 2018 in forum: Mods and Upgrades
  11. theman00011
    Post

    Worth upgrading to an E3D V6?

    I went ahead and got a V6 with a 0.25 nozzle as well. The V6 ended up being cheaper with free shipping from Printedsolid than a hexagon from Robo...
    Post by: theman00011, Jul 9, 2018 in forum: Mods and Upgrades
  12. theman00011
    Thread

    Worth upgrading to an E3D V6?

    Recently I was clearing a jam on my R1+ and broke the connection between the heat sink and heat block so I need to replace my hotend. I was...
    Thread by: theman00011, Jun 29, 2018, 9 replies, in forum: Mods and Upgrades
Showing results 1 to 12 of 12
Search Again