1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Finally!

Discussion in 'Show and Tell' started by PACNOR RC AEROSYSTEMS, Jan 19, 2016.

Page 2 of 3
  1. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Congrats !
     
    #21 Geof, Jan 25, 2016
  2. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    Finished product!


    12540529_10204035892536605_7825145089082445975_n.jpg
     
    #22 PACNOR RC AEROSYSTEMS, Jan 25, 2016
  3. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Looking good!
     
    #23 Geof, Jan 25, 2016
    PACNOR RC AEROSYSTEMS likes this.
  4. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    Now I am going to make this for my daughter!

    Capture.PNG
     
    #24 PACNOR RC AEROSYSTEMS, Jan 25, 2016
  5. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Lol going all out ! good luck! Post the finished !
     
    #25 Geof, Jan 25, 2016
  6. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    Will do!
     
    #26 PACNOR RC AEROSYSTEMS, Jan 25, 2016
  7. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,912
    Likes Received:
    7,338
    Big jump in difficulty :)
    Good luck.
     
    #27 mark tomlinson, Jan 25, 2016
  8. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Very big jump! I'm interested to see what mattercontrol does with it
     
    #28 Geof, Jan 25, 2016
  9. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    What do you mean like print settings? I was just going to use default PLA settings.
     
    #29 PACNOR RC AEROSYSTEMS, Jan 25, 2016
  10. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    I didn't have good luck with matter control but a ton of people have so I'm curious how it handles a more complex model
     
    #30 Geof, Jan 26, 2016
  11. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    More so just how it looks when finished
     
    #31 Geof, Jan 26, 2016
  12. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Ok in matter control to manually heat open matter control, click on settings&controls by the black circle with white arrow. Go to control tab and you'll see the preheat buttons
     
    #32 Geof, Jan 26, 2016
  13. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    I went a little less complex to start. I see some white looking diagonal lines in it but I don't know what is causing that. This part is 3.5000" x 4.0000".


    Medium Quality
    PLA
    HOT END 210 C
    Bed 50 C

    IMAG0041.jpg
     
    #33 PACNOR RC AEROSYSTEMS, Jan 26, 2016
    Mike Kelly likes this.
  14. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Looks like markings from the nozzle.
     
    #34 Geof, Jan 26, 2016
  15. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Looks good !
     
    #35 Geof, Jan 26, 2016
  16. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    I put three of these on the bed but it is only printing one right in the center? It should have started in the bottom left corner.
     
    #36 PACNOR RC AEROSYSTEMS, Jan 26, 2016
  17. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    How did you put 3 of them down ? You would have to pull up the file, copy/paste 2x arrange how you like then save the 3 as a seperate file and print that file.
     
    #37 Geof, Jan 26, 2016
  18. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    By pull up the file I mean the edit mode... Matter control had an odd way of doing it but it can be done. If you don't print the new file and just press print it prints the original 1 PC file
     
    #38 Geof, Jan 26, 2016
  19. PACNOR RC AEROSYSTEMS

    PACNOR RC AEROSYSTEMS Member

    Joined:
    Jan 2, 2016
    Messages:
    106
    Likes Received:
    18
    Oh you mean save it as a *NEW* G-Code, I see now. Oh well, I have to let this run for another 1h and 5min before it's done. Thanks brother. If any is in the Pacific Northwest close to Lake Stevens (WA State) and can come out to the house and help me this weekend it would be highly appreciated.
     
    #39 PACNOR RC AEROSYSTEMS, Jan 26, 2016
  20. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,757
    Likes Received:
    2,339
    Sorry man I'm in Illinois, but any issues or questions feel free to post or pm me. I'll do my best to help ya out
     
    #40 Geof, Jan 26, 2016
    PACNOR RC AEROSYSTEMS likes this.
Page 2 of 3

Share This Page