Partial Answer Printer stops, no error code. I saved the terminal output.

Jesse · Jun 16, 2016

Hi, Previously I had been getting a stop on some prints with the error: printer head cooled to much. So I made sure the thermistor was tight, and put a half cover over the printer. I got a successful print off, but now the printer is frozen mid print, and there is no error code.

Here's the terminal output:
Code:
<-ok T:214.9 /215.0 B:55.9 /55.0 T0:214.9 /215.0 @:84 B@:0 [6169.159]
->N70381 G1 X144.3 Y137.51 Z2.899 E4835.893*58 [6169.160]
<-ok [6169.167]
->N70382 G1 X140.93 Y134.15 Z2.899 E4835.972*9 [6169.168]
<-ok [6169.273]
->N70383 G1 X137.57 Y130.78 Z2.899 E4836.051*4 [6169.274]
<-ok [6169.388]
->N70384 G1 X134.2 Y127.42 Z2.899 E4836.131*56 [6169.389]
<-ok [6169.507]
->N70385 G1 X130.84 Y124.05 Z2.899 E4836.21*51 [6169.508]
<-ok [6169.626]
->N70386 G1 X127.47 Y120.69 Z2.899 E4836.289*7 [6169.627]
<-ok [6169.744]
->N70387 G1 X124.11 Y117.32 Z2.899 E4836.368*2 [6169.745]
<-ok [6169.863]
->N70388 G1 X120.74 Y113.96 Z2.899 E4836.447*10 [6169.864]
<-ok [6169.978]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526*1 [6169.979]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6171.980]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6173.981]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6174.497]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6174.999]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6175.500]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6176.001]
->N70389 G1 X117.38 Y110.59 Z2.899 E4836.526* [6178.459]
The print was going fine~ and then this happened at about 0.5 cm z axis.
Filament type: PLA
Extruding Temp: 215
Bed Temp: 55
Bed makeup: Glue stick

If anyone has an Idea on what might of caused this, I would be really grateful to hear.

mark tomlinson · Jun 16, 2016

You missed the actual error. You must save the entire console log to find the error otherwise it will quickly scroll off into never-never land.

mark tomlinson · Jun 16, 2016

If that IS the entire terminal log then blame the software because the printer did exactly what it was told

mark tomlinson · Jun 16, 2016

And actual error will look like this (just an example):

Send: N7G28 X0 Y0*53
Recv: ok
Send: N8G28 Z0*113
Recv: Error:Extruder switched off. Temperature fell too much during print!
Changing monitoring state from 'Printing' to 'Error: Extruder switched off. Temperature ...'
Recv: Errorrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)
Recv: ok

Jesse · Jun 16, 2016

Thank you, I found the error. It occurred right after the print started, but then it worked out for a few layers before the section that I posted above. I wonder if its just the model?

Code:

->Communication State: PreparingToPrint

->M105

<-ok T:214.1 /214.0 B:55.3 /55.0 T0:214.1 /214.0 @:46 B@:127
->M105

<-ok T:214.0 /214.0 B:56.1 /55.0 T0:214.0 /214.0 @:48 B@:127
->M105

<-ok T:213.9 /214.0 B:56.9 /55.0 T0:213.9 /214.0 @:51 B@:0
->N1 M110 S1*96

<-ok
->Communication State: Printing

->N2 G21*24 [0.116]

<-ok [0.131]

->N3 M107*38 [0.147]

<-ok [0.163]

->N4 M140 S55*81 [0.178]

<-ok [0.194]

->N5 G4 P1000*89 [0.209]

<-ok [1.223]

->N6 M105*33 [1.239]

<-ok T:214.1 /214.0 B:56.3 /55.0 T0:214.1 /214.0 @:48 B@:0 [1.255]

->N7 G4 P1000*91 [1.270]

<-ok [2.284]

->N8 M105*47 [2.300]

<-ok T:214.2 /214.0 B:56.1 /55.0 T0:214.2 /214.0 @:44 B@:0 [2.315]

->N9 G4 P1000*85 [2.331]

<-ok [3.345]

->N10 M105*22 [3.361]

<-ok T:214.1 /214.0 B:55.9 /55.0 T0:214.1 /214.0 @:47 B@:0 [3.376]

->N11 G4 P1000*108 [3.392]

<-ok [4.406]

->N12 M105*20 [4.421]

<-ok T:214.0 /214.0 B:55.8 /55.0 T0:214.0 /214.0 @:49 B@:0 [4.437]

->N13 G4 P1000*110 [4.452]

<-ok [5.466]

->N14 M105*18 [5.482]

<-ok T:214.0 /214.0 B:55.6 /55.0 T0:214.0 /214.0 @:49 B@:0 [5.498]

->N15 G4 P1000*104 [5.513]

<-ok [6.527]

->N16 M105*16 [6.543]

<-ok T:214.0 /214.0 B:55.5 /55.0 T0:214.0 /214.0 @:49 B@:0 [6.559]

->N17 M104 T0 S215*17 [6.574]

<-ok [6.590]

->N18 M104 T0 S215*30 [6.605]

<-ok [6.621]

->N19 T0*2 [6.636]

<-echo:Active Extruder: 0 [6.652]

<-ok [6.652]

->N20 G28 X0 Y0 Z0*106 [6.683]

->N20 G28 X0 Y0 Z0*10 [16.698]

->N20 G28 X0 Y0 Z0*10 [26.713]

<-ok [29.147]

<-Error:Line Number is not Last Line Number+1, Last Line: 20 [29.147]

<-Resend: 21 [29.147]

<-ok [29.147]

->N21 M105*20 [29.162]

<-ok T:215.4 /215.0 B:55.3 /55.0 T0:215.4 /215.0 @:50 B@:0 [29.178]

->N22 M114*23 [29.194]

<-X:0.00 Y:0.00 Z:-0.30 E:0.00 Count X: 0.00 Y:0.00 Z:-0.30 [29.209]

<-ok [29.212]

->N23 G1 X0 Y0 Z5 F5000*52 [29.225]

<-ok [29.240]

->N24 M104 S215*85 [29.256]

<-ok [29.272]

->N25 G4 P1000*107 [29.287]

<-ok [31.331]

->N26 M105*19 [31.346]

<-ok T:215.8 /215.0 B:55.1 /55.0 T0:215.8 /215.0 @:37 B@:0 [31.362]

->N27 G4 P1000*105 [31.378]

<-ok [32.392]

->N28 M105*29 [32.407]

<-ok T:215.4 /215.0 B:55.0 /55.0 T0:215.4 /215.0 @:51 B@:0 [32.423]

->N29 G28 X0 Y0 Z0*99 [32.439]

<-ok [36.292]

->N30 M105*20 [36.307]

<-ok T:214.9 /215.0 B:55.8 /55.0 T0:214.9 /215.0 @:62 B@:127 [36.323]

->N31 M114*21 [36.338]

<-X:0.00 Y:0.00 Z:-0.30 E:0.00 Count X: 0.00 Y:0.00 Z:-0.30 [36.354]

<-ok [36.354]

->N32 G29*35 [36.370]

<-Bed x: 15.00 y: 20.00 z: -0.29 [43.499]

->N32 G29*3 [46.385]

<-Bed x: 110.00 y: 20.00 z: 1.18 [46.712]

<-Bed x: 205.00 y: 20.00 z: 2.19 [50.004]

<-Bed x: 205.00 y: 125.00 z: 2.18 [53.592]

->N32 G29*3 [56.400]

<-Bed x: 110.00 y: 125.00 z: 1.14 [57.289]

<-Bed x: 15.00 y: 125.00 z: -0.41 [61.111]

<-Bed x: 15.00 y: 230.00 z: 0.10 [64.605]

->N32 G29*3 [66.415]

<-Bed x: 110.00 y: 230.00 z: 1.44 [67.850]

<-Bed x: 205.00 y: 230.00 z: 2.46 [71.157]

<-Eqn coefficients: a: 0.01 b: 0.00 d: -0.51 [71.157]

<-planeNormal x: -0.01 y: -0.00 z: 1.00 [71.157]

<-ok [71.157]

->N33 M105*23 [71.173]

<-echo:endstops hit:  Z:2.46 [71.173]

<-Error:Line Number is not Last Line Number+1, Last Line: 32 [71.204]

<-Resend: 33 [71.204]

<-ok [71.204]

->N33 M105*2 [71.219]

<-ok T:214.8 /215.0 B:55.9 /55.0 T0:214.8 /215.0 @:57 B@:0 [71.235]

->N34 M114*16 [71.251]

<-X:205.01 Y:230.00 Z:-0.30 E:0.00 Count X: 205.00 Y:230.00 Z:2.71 [71.266]

<-ok [71.266]

->N35 T0*12 [71.297]

<-echo:Active Extruder: 0 [71.329]

<-ok [71.329]

->N36 G90*37 [71.344]

<-ok [71.360]

->N37 G92 E0*115 [71.375]

<-ok [71.391]

->N38 M114*28 [71.407]

<-X:205.01 Y:230.00 Z:-0.30 E:0.00 Count X: 205.00 Y:230.00 Z:2.71 [71.422]

<-ok [71.422]

->N39 M82*35 [71.438]

<-ok [71.453]

->N40 M107*17 [71.500]

<-ok [71.516]

->N41 G1 X199.73 Y224.18 Z-0.133 F9000*3 [71.532]

<-ok [71.547]

->N42 G1 X194.45 Y218.36 Z0.033*72 [71.563]

<-ok [71.578]

->N43 G1 X189.17 Y212.53 Z0.2*73 [71.594]

<-ok [71.609]

->N44 G1 X183.89 Y206.71 Z0.366*71 [71.625]

<-ok [71.641]

->N45 G1 X178.62 Y200.89 Z0.533*64 [71.656]

<-ok [71.672]

->N46 G1 X173.34 Y195.07 Z0.699*65 [71.687]

<-ok [71.703]

->N47 G1 X168.06 Y189.24 Z0.866*73 [71.719]

<-ok [71.734]

->N48 G1 X162.78 Y183.42 Z1.032*71 [71.750]

<-ok [71.765]

->N49 G1 X157.5 Y177.6 Z1.199*65 [71.781]

<-ok [71.797]

->N50 G1*29 [71.828]

<-ok [71.843]

->N51 G1 F1200*121 [71.859]

<-ok [71.875]

->N52 G1 X155.48 Y177.6 Z1.199 E0.101 F2400*91 [71.891]

<-ok [71.906]

->N53 G1 X153.45 Y177.6 Z1.199 E0.202*49 [71.921]

<-ok [71.937]

->N54 G1 X151.43 Y177.6 Z1.199 E0.303*50 [71.953]

<-ok [71.968]

->N55 G1 X149.41 Y177.6 Z1.199 E0.404*56 [71.984]

<-ok [71.999]

->N56 G1 X147.38 Y177.6 Z1.199 E0.505*59 [72.015]

<-ok [72.031]

->N57 G1 X145.36 Y177.6 Z1.199 E0.606*54 [72.046]

<-ok [72.062]

->N58 G1 X143.34 Y177.6 Z1.199 E0.707*61 [72.077]

<-ok [72.093]

->N59 G1 X141.31 Y177.6 Z1.199 E0.808*59 [72.109]

<-ok [72.124]

->N60 G1 X139.29 Y177.6 Z1.199 E0.908*54 [72.140]

<-ok [72.155]

->N61 G1 X137.27 Y177.6 Z1.199 E1.009*62 [72.171]

<-ok [72.187]

->N62 M105*19 [72.202]

<-ok T:214.9 /215.0 B:55.8 /55.0 T0:214.9 /215.0 @:55 B@:0 [72.218]

->N63 G1 X135.24 Y177.6 Z1.199 E1.11*4 [72.233]

<-ok [72.249]

->N64 G1 X133.22 Y177.6 Z1.199 E1.211*49 [72.265]

<-ok [72.280]

->N65 G1 X131.2 Y177.6 Z1.199 E1.312*2 [72.296]

<-ok [72.311]

->N66 G1 X129.17 Y177.6 Z1.199 E1.413*58 [72.327]

<-ok [72.343]

->N67 G1 X127.15 Y177.6 Z1.199 E1.514*49 [72.358]

<-ok [72.374]

->N68 G1 X125.13 Y177.6 Z1.199 E1.615*56 [72.389]

<-ok [72.405]

->N69 G1 X123.1 Y177.6 Z1.199 E1.716*14 [72.421]

<-ok [72.436]

->N70 G1 X121.08 Y177.6 Z1.199 E1.817*51 [72.452]

<-ok [72.467]

->N71 G1 X119.06 Y177.6 Z1.199 E1.918*57 [72.483]

<-ok [72.499]

->N72 G1 X117.03 Y177.6 Z1.199 E2.019*58 [72.514]

<-ok [72.530]

->N73 G1 X115.01 Y177.6 Z1.199 E2.12*0 [72.545]

<-ok [72.561]

->N74 G1 X112.99 Y177.6 Z1.199 E2.221*51 [72.577]

<-ok [72.592]

->N75 G1 X110.96 Y177.6 Z1.199 E2.322*61 [72.608]

<-ok [72.623]

->N76 G1 X108.94 Y177.6 Z1.199 E2.423*51 [72.639]

<-ok [72.655]

->N77 G1 X106.92 Y177.6 Z1.199 E2.523*59 [72.670]

<-ok [72.686]

->N78 G1 X104.89 Y177.6 Z1.199 E2.624*56 [72.701]

<-ok [72.717]

->N79 G1 X102.87 Y177.6 Z1.199 E2.725*49 [72.733]

<-ok [72.779]

->N80 G1 X100.85 Y177.6 Z1.199 E2.826*59 [72.795]

<-ok [72.826]

->N81 G1 X98.82 Y177.6 Z1.199 E2.927*13 [72.842]

<-ok [72.873]

->N82 G1 X96.8 Y177.6 Z1.199 E3.028*53 [72.889]

<-ok [72.935]

->N83 G1 X94.78 Y177.6 Z1.199 E3.129*1 [72.951]

<-ok [72.982]

->N84 G1 X92.75 Y177.6 Z1.199 E3.23*54 [72.998]

<-ok [73.029]

->N85 G1 X90.73 Y177.6 Z1.199 E3.331*3 [73.045]

<-ok [73.076]

->N86 G1 X88.71 Y177.6 Z1.199 E3.432*15 [73.091]

<-ok [73.123]

->N87 G1 X86.69 Y177.6 Z1.199 E3.533*9 [73.138]

<-ok [73.185]

->N88 G1 X84.66 Y177.6 Z1.199 E3.634*15 [73.201]

<-ok [73.232]

->N89 M105*22 [73.247]

<-ok T:214.9 /215.0 B:55.7 /55.0 T0:214.9 /215.0 @:53 B@:0 [73.279]

->N90 G1 X82.64 Y177.6 Z1.199 E3.735*2 [73.294]

mark tomlinson · Jun 16, 2016

There is no error in that terminal.
The "<-Error:Line Number is not Last Line Number+1, Last Line: 32 [71.204]"
Is really a warning and will not generally impact the printer in any way, but if it proves anything it proves you might be having a communications error with the printer and the computer. This would cause these sorts of errors and the printer might well just stop.

I see no explicit errors in that terminal output or in the first one you posted.
Something else is stopping the print,probably the software you are using (just a guess) or a bad USB cable.

Make sure you use a new USB cable and you might try a powered hub between the printer and the computer.

Jesse · Jun 16, 2016

I would definitely think its the USB. After checking my cable I noticed some chunks missing from my cat chewing on it>> Thanks for the heads up on the powered hub, that makes a lot of sense, and I'll try that if things don't improve with a new cable.

Michael Keyser · Jan 29, 2017

Jesse said: ↑

I would definitely think its the USB. After checking my cable I noticed some chunks missing from my cat chewing on it>> Thanks for the heads up on the powered hub, that makes a lot of sense, and I'll try that if things don't improve with a new cable.
Click to expand...

I know it's been a while, but did any of those proposed items solve your problem. And, if they did, do you know which specifically helped?

Thanks!

mark tomlinson · Jan 29, 2017

He has not logged on since June of last year.
I rather doubt he is going to answer you

Geof · Jan 29, 2017

Michael Keyser said: ↑

I know it's been a while, but did any of those proposed items solve your problem. And, if they did, do you know which specifically helped?

Thanks!
Click to expand...

If your having an issue please feel free to start a thread in troubleshooting, many will be able to help out

Partial Answer Printer stops, no error code. I saved the terminal output.

Jesse New Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

Jesse New Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

Jesse New Member

Michael Keyser New Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

Geof Volunteer Moderator
Staff Member

Share This Page

About Us

Quick Navigation

Like us on Facebook

Useful Searches

Partial Answer Printer stops, no error code. I saved the terminal output.

Jesse New Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ Staff Member

Jesse New Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ Staff Member

Jesse New Member

Michael Keyser New Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ Staff Member

Geof Volunteer Moderator Staff Member

Share This Page

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

mark tomlinson ༼ つ ◕_ ◕ ༽つ
Staff Member

Geof Volunteer Moderator
Staff Member