1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
  2. Please message Harry if you experience any technical difficulties while using the forum. Thank you.

Shoutbox Archive

Discussion in 'Archive' started by Harry, Mar 4, 2015.

  1. TaigaChat

    TaigaChat Guest

    Feb 15, 2017 4:47 AM - Bill Monroe: good morning
    Feb 15, 2017 7:13 AM - daniel871: For the step calibration, if you don't want to fool with firmware directly you could just define it in starting Gcode in your slicer with M92.
    Feb 15, 2017 7:13 AM - daniel871: http://reprap.org/wiki/G-code#M92:_Set_axis_steps_per_unit
    Feb 15, 2017 7:44 AM - Malte: Okay but what should the z steps/mm be for the r1 refurbished
    Feb 15, 2017 8:35 AM - daniel871: Depends on whether is has 5/16 threaded rods or 8mm threaded rods or the integrated leadscrews.
    Feb 15, 2017 8:36 AM - daniel871: Get the firmware for the version you have and flash it as the starting point before you just start fiddling and really screw things up. http://guide.robo3d.com/Wiki/ROBO_3D_Firmware_Release_Notes#Section_Old_ROBO_R1_Firmware
    Feb 15, 2017 8:50 AM - Malte: I printed a 20 mm cube with the RoBo3DR1V3 firmware and the cube was at 20mm all directions, i think it was that i had the rc8 firmware
    Feb 15, 2017 8:51 AM - Malte: but it has strange ripples in the print
    Feb 15, 2017 9:11 AM - WheresWaldo: Likely you had the incorrect RC8, You have to download the one that matches the leadscrew/threaded rods or modify the steps yourself.
    Feb 15, 2017 9:34 AM - Malte: I copied the steps/mm from the RoBo3DR1V3 firmware into rc8 and currently testing a 20mm cube
    Feb 15, 2017 9:34 AM - Malte: what leadscrew is RoBo3DR1V3 designed for?
    Feb 15, 2017 9:39 AM - WheresWaldo: 8mm
    Feb 15, 2017 9:46 AM - Malte: okay so if it printed perfect with that firmware does that mean i have a 8mm rod?
    Feb 15, 2017 10:46 AM - WheresWaldo: Yep
    Feb 15, 2017 12:39 PM - daniel871: [​IMG]
     
  2. TaigaChat

    TaigaChat Guest

    Feb 16, 2017 6:10 AM - NFOsec: Fellow 3DPCosmonaults.
    Feb 16, 2017 8:22 AM - toymaker: yo
     
  3. TaigaChat

    TaigaChat Guest

  4. TaigaChat

    TaigaChat Guest

    Feb 17, 2017 8:01 PM - toymaker: quiet around here...?
    Feb 17, 2017 8:15 PM - Quest: yes it is
    Feb 18, 2017 5:54 AM - JOAQUIN PICCI: Hello from argentina
    Feb 18, 2017 5:56 AM - Bill Monroe: Hello from USA
     
  5. TaigaChat

    TaigaChat Guest

    Feb 19, 2017 8:26 AM - Malte: Hey i have a problem, i tried using vase mode for the first time and i noticed that the motors slowed down when it was at the top and then it speeds up again
    Feb 19, 2017 8:28 AM - Malte: like it wassnt getting enough power or something
     
  6. TaigaChat

    TaigaChat Guest

    Feb 19, 2017 at 11:22 PM - Jerry RoBo 3D: could be a setting for layer cooling that delays the layer by slowing down the print speed
    Feb 19, 2017 at 11:23 PM - Jerry RoBo 3D: smaller layers will get printed slower
    Feb 19, 2017 at 11:23 PM - Jerry RoBo 3D: so they have time to cool
    Feb 20, 2017 at 4:18 AM - daniel871: http://i.imgur.com/vZpH4A4.gifv
    Feb 20, 2017 at 8:06 AM - toymaker: ive printed some 200mb plus stls, and while printing if i use print preview in repetier it can slow down the motors
    Feb 20, 2017 at 8:07 AM - toymaker: i got 16 of ram... so im not too sure if it is a memory issue, i just learned not to mess with the print prewiew stuff on very large files
     
  7. TaigaChat

    TaigaChat Guest

  8. TaigaChat

    TaigaChat Guest

    Feb 22, 2017 at 6:23 AM - Soupaboy: It's been a while, hello all
     
  9. TaigaChat

    TaigaChat Guest

Share This Page