1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Bd182

  1. Bd182
    Post

    Solved Z offset suddenly changes

    Good to know that I'm not operating off the reservation. And, I added a sheet of float glass last year too after my fancy-pants "hard glass"...
    Post by: Bd182, Jul 9, 2020 in forum: Troubleshooting
  2. Bd182
    Post

    Solved Z offset suddenly changes

    I found the auto leveling procedure tedious and disabled it last year. I have seen no disadvantage in that, and for months all my prints have had...
    Post by: Bd182, Jul 8, 2020 in forum: Troubleshooting
  3. Bd182
    Post

    Solved Z offset suddenly changes

    Thanks Mark- I see no play in the carriage bolts and the carriage is level to within 1/8". If I wiggle the bed up and down at the front edge, it...
    Post by: Bd182, Jul 8, 2020 in forum: Troubleshooting
  4. Bd182
    Thread

    Solved Z offset suddenly changes

    I've been printing for a year with Z offset of 0.3mm. Suddenly I was dragging the head on the glass, and I had to set Z offset to 1.0. A week...
    Thread by: Bd182, Jul 8, 2020, 7 replies, in forum: Troubleshooting
  5. Bd182
    Post

    Solved Marlin 1.1

    Mark- Thanks for taking the trouble to suss this out. I am not aware of a FAQ post on this topic or a "SDBASE.ZIP" file. Can you share a link to...
    Post by: Bd182, Mar 13, 2019 in forum: Troubleshooting
  6. Bd182
    Post

    Solved Marlin 1.1

    Oops, you said Configuration.h....
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  7. Bd182
    Post

    Solved Marlin 1.1

    All files came from the official Robo firmware download on the Robo page.
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  8. Bd182
    Post

    Solved Marlin 1.1

    It's the bed leveling that I'm frustrated with. I've turned it off in favor of manual leveling. How do people get educated on how to implement a...
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  9. Bd182
    Post

    Solved Marlin 1.1

    I don't care so much about Marlin 1.0, except as a backup for failures of the transition to 1.1. As a new user, perhaps I'll just run with what I...
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  10. Bd182
    Post

    Solved Marlin 1.1

    There are over 500 errors, leading me to believe there's something seriously flawed in the posted firmware. Jason at Robo says he knows nothing...
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  11. Bd182
    Post

    Solved Marlin 1.1

    If you mean "Updating firmware with Arduino", then yes. The errors appear when I tell Arduino to verify the downloaded package, even with Arduino...
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  12. Bd182
    Post

    Solved Marlin 1.1

    I am beginning to look more closely at changing my firmware, and towards that end I've downloaded the stock Robo firmware and the Marlin 1.1.x...
    Post by: Bd182, Mar 12, 2019 in forum: Troubleshooting
  13. Bd182
    Post

    Aux4 on RAMPS board

    I printed a bracket to hold a microswitch to the smooth rod of my Z axis. At the end of each print I can program a rise to kiss the switch and...
    Post by: Bd182, Mar 11, 2019 in forum: Mods and Upgrades
  14. Bd182
    Post

    Aux4 on RAMPS board

    I had narrowed in on motherboard 33. It seems many other people have asked the Marlin wizards why M42 does not work for them, and no one has...
    Post by: Bd182, Mar 11, 2019 in forum: Mods and Upgrades