1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by colton81

  1. colton81
    Post

    Someone to quote a print

    Pm sent Sent from my iPhone using Tapatalk
    Post by: colton81, Dec 26, 2017 in forum: Off Topic
  2. colton81
    Thread

    Someone to quote a print

    I am needing someone that can print large pieces for a figurine, or if possible all in one piece. The max size of the model is scaled up 400%...
    Thread by: colton81, Dec 26, 2017, 4 replies, in forum: Off Topic
  3. colton81
    Post

    Connecting a heated bed

    I’m pretty much just repurposing the robo board just to see if I can do it if it doesn’t work then I’ll switch to the other board I have....
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  4. colton81
    Post

    Connecting a heated bed

    Its the same power supply I’m using for bot the heated bed and the power to the main board. I figured it really isn’t a good idea to try to use...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  5. colton81
    Post

    Connecting a heated bed

    I wish there was a way to bypass the onboard mossfett and use an external I think that might end up working. But I’m assuming everything is...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  6. colton81
    Post

    Connecting a heated bed

    @Kilrah lol just saw your post about the fuse blowing... that’s exactly what happened but it blew before I could even try to test it. Sent from...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  7. colton81
    Post

    Connecting a heated bed

    Well I decided to give it a go.... unfortunately. I connected the bed power in to the same psu I’m using to power the main board and turned it on...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  8. colton81
    Post

    Connecting a heated bed

    Something else I noticed. I’m not using the standard power in plug. I’m using the power in pins from my psu and next to it says bed power in. I’m...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  9. colton81
    Post

    Connecting a heated bed

    Well I did just a test to see if it would try to heat up and it doesn’t budge it’s like it’s not outputting any voltage. I wonder if the firmware...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  10. colton81
    Post

    Connecting a heated bed

    [IMG] This is the bed any idea how I could tell on the bed it’s self they don’t really give much information on their website Sent from my...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  11. colton81
    Post

    Connecting a heated bed

    The board is supposedly 19amps at 12v so if I’m correct wouldnt the main board give out or the bed? Sent from my iPhone using Tapatalk
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  12. colton81
    Post

    Connecting a heated bed

    It didn’t snap to me until last night when I was going to connect the bed to the board that my heated bed is a 12v bed and this is the printer I...
    Post by: colton81, Dec 15, 2017 in forum: Mods and Upgrades
  13. colton81
    Post

    Connecting a heated bed

    Thanks for the pictures that helps. I will try again connecting. I tried connecting one wire to both positives and one wire to both negatives but...
    Post by: colton81, Dec 14, 2017 in forum: Mods and Upgrades
  14. colton81
    Post

    Connecting a heated bed

    That’s what I thought but maybe my meter was just acting up. I am powering the board with a 24v PSU and connected the power through the 2 green...
    Post by: colton81, Dec 14, 2017 in forum: Mods and Upgrades