1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Ender

  1. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    Do you have to do that before you run the PID tuning through MatterControl? So the order of steps is to enable PIDTEMPBED, upload new firmware,...
    Post by: Ender, Dec 9, 2017 in forum: Troubleshooting
  2. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    Here is my configuration.h I am using.
    Post by: Ender, Dec 9, 2017 in forum: Troubleshooting
  3. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    The first test I ran right after the upgrade, the bed heated to 40C and I watched the SSR turn off and on while maintaining that temp. Everything...
    Post by: Ender, Dec 9, 2017 in forum: Troubleshooting
  4. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    The SSR is rated for 40A.. As soon as I turn on the machine the bed heats. I will unplug it and try to heat the extruder. Last time I tried to...
    Post by: Ender, Dec 9, 2017 in forum: Troubleshooting
  5. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    I think another SSR just got burned up . I set the bed to 50C and it just keep rising, turned the machine off at 58C. Now the bed will heat...
    Post by: Ender, Dec 8, 2017 in forum: Troubleshooting
  6. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    I got the new bed and SSR installed. I started the PID loop in MatterControl using the show terminal feature. M303 E-1 C8 S70 I enter that...
    Post by: Ender, Dec 8, 2017 in forum: Troubleshooting
  7. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    I did smell some burning but only when I shoved my nose right up against the machine. The smell got worst as time went on though. And this is what...
    Post by: Ender, Dec 6, 2017 in forum: Troubleshooting
  8. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    What would your guess be, too hot, counterfeit, or bad wiring? NOTE: the right side of the SSR in the picture is the load side.
    Post by: Ender, Dec 6, 2017 in forum: Troubleshooting
  9. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    The one in the link is a Fotek with the corner cut rated for 40A. The max my PSU can provide is 30A and the max the bed should pull is 25A....
    Post by: Ender, Dec 6, 2017 in forum: Troubleshooting
  10. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    I am starting to wondering if the switch in the SSR burnt up and just opened the flood gates and the bed is heating up too fast. The temperature...
    Post by: Ender, Dec 5, 2017 in forum: Troubleshooting
  11. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    I AM USING 300W!! I have said this 3 times.
    Post by: Ender, Dec 5, 2017 in forum: Troubleshooting
  12. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    Well I just installed 6mm borosilicate glass, and it shattered on the first cycle to 90C! So not even tempered glass can withstand the...
    Post by: Ender, Dec 5, 2017 in forum: Troubleshooting
  13. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    I guess i assumed the heater would heat evenly. Thanks for the info! You got me thinking. I have read a lot about glass vs aluminum bed, but it...
    Post by: Ender, Dec 2, 2017 in forum: Troubleshooting
  14. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    Hmm I wish those details about normal glass not working when in direct contact with the heater was more evident before I tried it. Read some many...
    Post by: Ender, Dec 2, 2017 in forum: Troubleshooting
  15. Ender
    Post

    Unresolved KEENOVO Silicone Heater Upgrade - R1+

    While I do appreciate the replies, it seems like neither one of you read my comments. I am using a 300W heater at 12V and the glass shattered...
    Post by: Ender, Dec 2, 2017 in forum: Troubleshooting