1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Goofynoodle

  1. Goofynoodle
    Post

    Unresolved Removing Extruder Assembly

    [MEDIA] my video on removing the hot end for newer robo.
    Post by: Goofynoodle, Dec 28, 2016 in forum: Troubleshooting
  2. Goofynoodle
    Post

    Partially Solved Removing hot end

    [MEDIA] this may help..... just don't push up too hard while turning the screw.... it's a captive nut in there and pushing up will push nut out...
    Post by: Goofynoodle, Dec 28, 2016 in forum: Troubleshooting
  3. Goofynoodle
    Post

    Hot end removal on a new Robo 3D R1 Plus

    [MEDIA]..... this is my video on how to remove it.
    Post by: Goofynoodle, Dec 28, 2016 in forum: General Questions
  4. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    i'm just using it cause it came with the printer (robor1+) it already has all the settings for the printer set up... like bed size and such...so...
    Post by: Goofynoodle, Dec 7, 2016 in forum: Troubleshooting
  5. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    I uninstalled mattercontrol, deleted the files for a clean reinstall.....and once I reinstalled.... all my settings are still there. soooooooo.......
    Post by: Goofynoodle, Dec 7, 2016 in forum: Troubleshooting
  6. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    while i'm at it.... is there a way to get the Arduino files to reset the printer itself? and I literally am going on the info that I got with my...
    Post by: Goofynoodle, Dec 7, 2016 in forum: Troubleshooting
  7. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    I see... well... I uninstalled my printer from matter control in hopes of resetting all that stuff back to default cause I added that z lift...
    Post by: Goofynoodle, Dec 7, 2016 in forum: Troubleshooting
  8. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    ok...I put in the code to raise nozzle on z axis .5mm ......... when my test print was done, the nozzle dropped to .5mm above the...
    Post by: Goofynoodle, Dec 6, 2016 in forum: Troubleshooting
  9. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    I saw this M104 S0; Set Hot-end to 0C (off) M140 S0; Set bed to 0C (off) just stick it in the end gcode?
    Post by: Goofynoodle, Dec 6, 2016 in forum: Troubleshooting
  10. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    oh and while were talking gcode..... my bed stays on when printing from sd card.....
    Post by: Goofynoodle, Dec 6, 2016 in forum: Troubleshooting
  11. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    [ATTACH]
    Post by: Goofynoodle, Dec 6, 2016 in forum: Troubleshooting
  12. Goofynoodle
    Post

    Partially Solved hot end lift settings?

    At the risk of sounding ignorant...... I just do what now? in mattercontrol.... where would one find that? matter control has 3 settings for...
    Post by: Goofynoodle, Dec 6, 2016 in forum: Troubleshooting
  13. Goofynoodle
    Thread

    Partially Solved hot end lift settings?

    Is there a way to get the hot end to raise a little bit after bed leveling and / or after the print completes? I already have my z offset at .85...
    Thread by: Goofynoodle, Dec 6, 2016, 20 replies, in forum: Troubleshooting
  14. Goofynoodle
    Post

    Solved black abs stripping

    UPDATE!!! I Started thinking " who can I trust?" so, I ordered black abs from robo3d. guess what.... full speed 240degrees, and lookin...
    Post by: Goofynoodle, Dec 6, 2016 in forum: Troubleshooting