1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Hobbit

  1. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Screws are tightened again on both. Still leaning the same amount. Should I tighten the belt more then?
    Post by: Hobbit, Jan 14, 2017 in forum: Troubleshooting
  2. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Ok I'll get it a shot when I get home! Thanks, you're the man!
    Post by: Hobbit, Jan 13, 2017 in forum: Troubleshooting
  3. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Are you talking about the timing pulley screws or the the screws where the belt ends? Or are you saying to tighten the belt?
    Post by: Hobbit, Jan 13, 2017 in forum: Troubleshooting
  4. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Thank you again for all the help. With the bed belt, I think it's pretty tight but I mean how tight should it be? I assume not crazy tight? I...
    Post by: Hobbit, Jan 12, 2017 in forum: Troubleshooting
  5. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Sorry for the confusion everyone. I want to do(atleast trying to do) the mesh leveling so I should remove: M565 Z-.4; set the offset for...
    Post by: Hobbit, Jan 12, 2017 in forum: Troubleshooting
  6. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Hey guys, I was able to print the first part of my LCD case without an issue it seems. I then printed a taller barrel piece and I can see about...
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  7. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Awesome thank you for that. I'm doing another now and will report back. UPDATE: -.5 seems to be the winner for me! Something I noticed though was...
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  8. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Thanks guys! here is -.6. Should I go lower still?
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  9. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Ok I adjusted the off set to -.8 and printed a test model. I think it's still to far away from the bed? I adjusted the z to -.6 and am running...
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  10. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Thanks! I'm setting up a test print right now. I'll let everyone know how it goes.
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  11. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Thanks everyone! I adjusted my starting script to this: G28 X0 Y0 Z0 ; home all axes G1 Z5 F5000 ; lift nozzle G28 X0 Y0 Z0 ; Home Z again in...
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  12. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    This is what I have in the start up script: G28 X0 Y0 Z0 ; home all axes G1 Z5 F5000 ; lift nozzle M109 S[temperature] ; set the extruder temp...
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  13. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    Ok I have updated the firmware to the RCBF for the R1+. I still have the issue of when I start a print via the LCD the bed heats up, the nozzle...
    Post by: Hobbit, Jan 11, 2017 in forum: Troubleshooting
  14. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    So my glass bed is warped? What do I do? How can I level a warped bed? Should I update my firmware?
    Post by: Hobbit, Jan 10, 2017 in forum: Troubleshooting
  15. Hobbit
    Post

    Unanswered Robo R1+ Issues (Leaning + LCD Contoller)

    I'm struggling with the mattercontrol software and trying to get a paper level test done. This is what my readout is with I m29: <-Bed x: 15.00...
    Post by: Hobbit, Jan 10, 2017 in forum: Troubleshooting