1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by jccbsl

  1. jccbsl
    Post

    Solved R1+ Profile for PrusaSlicer?

    No reason you can't as far as I know. Please try it and report back!
    Post by: jccbsl, May 18, 2021 in forum: Troubleshooting
  2. jccbsl
    Post

    Solved R1+ Profile for PrusaSlicer?

    If you're looking for a great tutorial on creating custom PrusaSlicer profiles, Tom Sanladerer has one: [MEDIA]
    Post by: jccbsl, Dec 24, 2020 in forum: Troubleshooting
  3. jccbsl
    Post

    Unanswered Prusaslicer (Slic3r PE) Settings R1

    Thanks, Mark, You're exactly right. I re-sliced the file and it prints just fine. I'm not sure what was off, but I can't argue with results.
    Post by: jccbsl, Nov 14, 2020 in forum: General Questions
  4. jccbsl
    Post

    Solved R1+ Profile for PrusaSlicer?

    This configuration bundle seems to work.
    Post by: jccbsl, Nov 13, 2020 in forum: Troubleshooting
  5. jccbsl
    Post

    Unanswered Prusaslicer (Slic3r PE) Settings R1

    I found a configuration file for Slic3r, the forerunner of PrusaSlicer, which appears to work on my R1+. However, since I have replaced the glass...
    Post by: jccbsl, Nov 13, 2020 in forum: General Questions
  6. jccbsl
    Thread

    Solved R1+ Profile for PrusaSlicer?

    I'm looking for an R1+ profile for PrusaSlicer. Has anyone successfully created one?
    Thread by: jccbsl, Nov 8, 2020, 6 replies, in forum: Troubleshooting
  7. jccbsl
    Thread

    Unresolved Mesh Bed Leveling Tutorial?

    I'm looking for a step by step mesh bed leveling tutorial for the R1+. I have the bed level left to right, but the bed is off significantly...
    Thread by: jccbsl, Apr 16, 2020, 1 replies, in forum: Troubleshooting
  8. jccbsl
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Thanks, Mark! I had just finished inputting them after reading through several of your previous posts. That's exactly what the problem was.
    Post by: jccbsl, Feb 4, 2020 in forum: Mods and Upgrades
  9. jccbsl
    Post

    Community Favorite E3D v6 Information and Installation Guide

    BTW, the image I attached was taken before the changes (just in case somebody suspects that I forgot to save the changes).
    Post by: jccbsl, Feb 4, 2020 in forum: Mods and Upgrades
  10. jccbsl
    Post

    Community Favorite E3D v6 Information and Installation Guide

    OK, I'm confused... Marking the filament at 150mm, I had 65mm remaining once I sent the G1E100F90 command. Subtracting 65 from 150 gives me 85...
    Post by: jccbsl, Feb 4, 2020 in forum: Mods and Upgrades
  11. jccbsl
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Post by: jccbsl, Feb 4, 2020 in forum: Mods and Upgrades
  12. jccbsl
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Good to know. Thanks.
    Post by: jccbsl, Jan 26, 2020 in forum: Mods and Upgrades
  13. jccbsl
    Post

    Community Favorite E3D v6 Information and Installation Guide

    I had assumed that I could save the values using the M500 command.
    Post by: jccbsl, Jan 26, 2020 in forum: Mods and Upgrades