1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Jeffrey Wheeless

  1. Jeffrey Wheeless
    Post

    Please Send Help

    Just in case anyone finds this in the future and has any if the same issues here's some of the stuff I found that helped greatly: - M10 bolts on...
    Post by: Jeffrey Wheeless, May 27, 2016 in forum: Troubleshooting
  2. Jeffrey Wheeless
    Post

    Please Send Help

    It works and I think it works within the range of acceptable temperatures, although if you know what hot is considered let me know. But everything...
    Post by: Jeffrey Wheeless, May 21, 2016 in forum: Troubleshooting
  3. Jeffrey Wheeless
    Post

    Please Send Help

    PROGRESS HAS BEEN MADE!!! 2 of the controllers give off nothing at all, the y (meaning x at this point sorry) and the z, the other two have been...
    Post by: Jeffrey Wheeless, May 21, 2016 in forum: Troubleshooting
  4. Jeffrey Wheeless
    Post

    Please Send Help

    See the pain is its so difficult to figure out the decimals for them, I can aim for 1.7 though. Side note some of them didn't show any voltage at...
    Post by: Jeffrey Wheeless, May 21, 2016 in forum: Troubleshooting
  5. Jeffrey Wheeless
    Post

    Please Send Help

    Well the videos and stuff didn't exactly give you a good showing of what to do when something goes wrong. For whatever reason my digital...
    Post by: Jeffrey Wheeless, May 21, 2016 in forum: Troubleshooting
  6. Jeffrey Wheeless
    Post

    Please Send Help

    By the way, I don't think I've properly thanked both of you for all the work you've done helping me. You both have really gone above and beyond...
    Post by: Jeffrey Wheeless, May 19, 2016 in forum: Troubleshooting
  7. Jeffrey Wheeless
    Post

    Please Send Help

    The only place that sells the things for a multimeter that have the clips on them is an hour's drive away, so out of spite I've ordered them and a...
    Post by: Jeffrey Wheeless, May 19, 2016 in forum: Troubleshooting
  8. Jeffrey Wheeless
    Post

    Please Send Help

    So is it worth it to do the whole bread board and PSU stuff or can i get by with a multimeter and a USB plug?
    Post by: Jeffrey Wheeless, May 19, 2016 in forum: Troubleshooting
  9. Jeffrey Wheeless
    Post

    Please Send Help

    To save me from doing math early, what voltage are you guys getting across your controllers?
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting
  10. Jeffrey Wheeless
    Post

    Please Send Help

    Then tomorrow I shall do it properly, meter and all
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting
  11. Jeffrey Wheeless
    Post

    Please Send Help

    All wires should be good now. Is it worth it to get the multi meter out and do the math and see the output on those controllers or should I just...
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting
  12. Jeffrey Wheeless
    Post

    Please Send Help

    So besides that I think that I have the x and y switched around there is improvement. The noise is greatly reduced and the y (responding to the x)...
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting
  13. Jeffrey Wheeless
    Post

    Please Send Help

    Oh you mean they all have jumpers gotcha! I will be back at the printer in about 45 min and I'm hopeful that this should do it cause usually...
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting
  14. Jeffrey Wheeless
    Post

    Please Send Help

    I think I must be blind cause I can't see any jumpers on your pic. 1a, 1b, VDD, or GND. Well I'm glad it seems to be a simple issue.
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting
  15. Jeffrey Wheeless
    Post

    Please Send Help

    I might not of done that. Here are the pictures. Pictures are of the plain board with no chips or jumpers and then I only put those chips on no...
    Post by: Jeffrey Wheeless, May 18, 2016 in forum: Troubleshooting