1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Joehsmash

  1. Joehsmash
    Post

    [Help] config.g for Kickstarter Robo3D

    sorry, i would have chimed in a little earlier but you know.. life lol i would have been useless any ways, i swapped out my orgional psu out for...
    Post by: Joehsmash, Jun 8, 2020 in forum: Software
  2. Joehsmash
    Post

    [Help] config.g for Kickstarter Robo3D

    Well currently using marlin you can use your nozzle to probe the bed where as swapping to duet you will be using rrf and they currently dont...
    Post by: Joehsmash, Jun 4, 2020 in forum: Software
  3. Joehsmash
    Post

    [Help] config.g for Kickstarter Robo3D

    im going to do a write up once im finally finished... just trying to get any answers takes FOREVER on the forum. and thats the only way to get...
    Post by: Joehsmash, Jun 2, 2020 in forum: Software
  4. Joehsmash
    Post

    [Help] config.g for Kickstarter Robo3D

    Here is my config.g now keep in mind i have a Duet 2 Wifi running RRF3.1.1 ; Configuration file for Duet WiFi (firmware version 3) ; executed by...
    Post by: Joehsmash, Jun 2, 2020 in forum: Software
  5. Joehsmash
    Post

    [Help] config.g for Kickstarter Robo3D

    Hey, i figure i would just chime in on this seeing as im actually doing this literally as we speak. and trying to work through most of the issues....
    Post by: Joehsmash, Jun 2, 2020 in forum: Software
  6. Joehsmash
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    @jim3Dbot Are you still around these forums? i have a question about your probe!
    Post by: Joehsmash, May 10, 2020 in forum: Mods and Upgrades
  7. Joehsmash
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Not sure if any one watching this thread is interested but i made a quick mount for these Ir sensors, i uploaded it to thingiverse...
    Post by: Joehsmash, Aug 29, 2017 in forum: Mods and Upgrades
  8. Joehsmash
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Also, i understand that you are able to save more than one Bed profile, how do you load/unload different save points?
    Post by: Joehsmash, Aug 20, 2017 in forum: Mods and Upgrades
  9. Joehsmash
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I honestly couldnt get a good read with auto UBL, the stock glass bed has too much flex. if you do a manual probe (7-9 points) it works way...
    Post by: Joehsmash, Aug 20, 2017 in forum: Mods and Upgrades
  10. Joehsmash
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Is any one else having trouble with the eeprom not saving the bed level information from UBL after you turn the power off on the printer? ever...
    Post by: Joehsmash, Aug 19, 2017 in forum: Mods and Upgrades
  11. Joehsmash
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I just went through this exact same problem. The issue that your going to run into with abl is that there is too much flex in the standard glass...
    Post by: Joehsmash, Aug 5, 2017 in forum: Mods and Upgrades
  12. Joehsmash
    Post

    Solved Ready to smash this pos

    Nothing physical has changed since I went from version 3.0 firmware (robo firmware) I can check. But last tear down I lubed everything. Going to...
    Post by: Joehsmash, Aug 4, 2017 in forum: Troubleshooting
  13. Joehsmash
    Post

    Solved Ready to smash this pos

    I 100% agree with you. How ever if you look at the last photo posted you can clearly see a big issue. The problem isn't such a simple one in that...
    Post by: Joehsmash, Aug 4, 2017 in forum: Troubleshooting
  14. Joehsmash
    Post

    Solved Ready to smash this pos

    That photo was blurry
    Post by: Joehsmash, Aug 4, 2017 in forum: Troubleshooting
  15. Joehsmash
    Post

    Solved Ready to smash this pos

    Once I figure out all of my problems I will make a list of solutions, currently having what I think is an over extrusion issue, will trouble shoot...
    Post by: Joehsmash, Aug 4, 2017 in forum: Troubleshooting