1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by jsam

  1. jsam
    Post

    Solved PEI Upgrade and z-offset

    Hey guys, it looks like I've got that elephant foot fixed thanks to your script help. I ran a few single layer prints as suggested and settled on...
    Post by: jsam, Nov 6, 2016 in forum: General Questions
  2. jsam
    Post

    Solved PEI Upgrade and z-offset

    Mark, I found this thread from July where you posted your starting script:...
    Post by: jsam, Nov 5, 2016 in forum: General Questions
  3. jsam
    Post

    Solved PEI Upgrade and z-offset

    Did a manual level with paper, that was a little off so better now. I tried a print with a lower bed temperature but not much improvement. It...
    Post by: jsam, Nov 5, 2016 in forum: General Questions
  4. jsam
    Post

    Solved PEI Upgrade and z-offset

    I use a Mac at home and don't have Notepad. I tried to open it up in the equivalent but it didn't seem to work. I'll try to open the file on my...
    Post by: jsam, Nov 4, 2016 in forum: General Questions
  5. jsam
    Post

    Solved PEI Upgrade and z-offset

    That sounds like a plan danzca6, how do you look a that g-code? Do you import it into a simple text editor or is there something in S3D that will...
    Post by: jsam, Nov 4, 2016 in forum: General Questions
  6. jsam
    Post

    Solved PEI Upgrade and z-offset

    Thanks for pointing that out Robert55, so if I change the Z-axis number (keeping it postive) the nozzle will be further away from the bed correct?...
    Post by: jsam, Nov 4, 2016 in forum: General Questions
  7. jsam
    Post

    PEI Print Bed

    Hi guys, I just did this upgrade to my Robo and won't get a chance to print until this weekend. I was wondering about the autoleveling sequence...
    Post by: jsam, Nov 3, 2016 in forum: Mods and Upgrades
  8. jsam
    Post

    Solved PEI Upgrade and z-offset

    Yes, this is the first time I've looked at the starting script in S3D and I haven't touched any script since I started using it.
    Post by: jsam, Nov 2, 2016 in forum: General Questions
  9. jsam
    Post

    Solved PEI Upgrade and z-offset

    I found the starting script in the FFF profile and I'm not seeing M565, I'm seeing this: G28 ; home all axes G29 ; probe the bed G1 Z5 F5000 ;...
    Post by: jsam, Nov 2, 2016 in forum: General Questions
  10. jsam
    Thread

    Solved PEI Upgrade and z-offset

    So my glass bed chipped earlier this week and I decided to upgrade the bed by adding a sheet of PEI. I used this youtube vid as a guide: [MEDIA]...
    Thread by: jsam, Nov 2, 2016, 20 replies, in forum: General Questions
  11. jsam
    Thread

    Leaving filament loaded in the printer

    Hi guys, Here's another newbie question. Should I leave the filament loaded in the printer after I am done printing for the day or should I...
    Thread by: jsam, Sep 7, 2016, 10 replies, in forum: General Questions
  12. jsam
    Post

    Solved Help with bed leveling switch

    Danzca6, I did the paper level and a few test prints, looks like I'm back in business. Thanks again for the help.
    Post by: jsam, Sep 2, 2016 in forum: Troubleshooting
  13. jsam
    Post

    Solved Help with bed leveling switch

    Thanks danzca6. What's the best way to make sure the x-axis is as level as possible?
    Post by: jsam, Aug 31, 2016 in forum: Troubleshooting