1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Marcos Zuccaro

  1. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    This is all yours guys ! thanks a lot for everything ! the time, the patience !! everything! Just thanks! after a few small parts now im printing...
    Post by: Marcos Zuccaro, Jun 25, 2017 in forum: Troubleshooting
  2. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Tried a lot in differents positions and tightenings, same error message. The first picture its a really bad one but i can tell that both...
    Post by: Marcos Zuccaro, Jun 24, 2017 in forum: Troubleshooting
  3. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    When i start up i get the message of maxtemp. Then MC says its 0º / 0º and if i move the thermistor cable a little bit the temperature reading...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  4. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    i done it , but now i have the message : "Error reported : Extruder switched off. MAXTEMP triggered!" when i start it ... every connection its...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  5. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    firs problem as soon as trying to put it in ... i tried to set the latch back into position but its looks like the hot end its too big to let the...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  6. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Great bro im assemblying it and give it a try... brb ! thx again ! the beer i owe you just turned into a whiskey ! ^^
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  7. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    oh okey, i was worried about that gap... i couldnt make it even... the rest looks great... i dont know if i have to tighten it up a little bit...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  8. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Hey guys ! MR annoying here again !...Hmmm i manage to put everything back together but even hot i cant finish tightening the nozzle. here is a...
    Post by: Marcos Zuccaro, Jun 23, 2017 in forum: Troubleshooting
  9. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    I forgot i had an allen like tool that came with the R1+ that fits perfectly trough the hole. It worked like wonders ! im gonna let it cool and...
    Post by: Marcos Zuccaro, Jun 22, 2017 in forum: Troubleshooting
  10. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Thanks for your replies guys ! Im in Argentina ^^ far south of the continent haha. I managed to remove both , thermistor and heater should i...
    Post by: Marcos Zuccaro, Jun 22, 2017 in forum: Troubleshooting
  11. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    So i did the disassembly of the hotend... i removed the nozzle and it looks unobstructed. I have some doubts about the heatbreak/heatblock part......
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  12. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    You have surpassed the limits of awesomeness! Thank you! I will update if everything worked and close it!
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  13. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    okey then... dissasembling everything it is ! hahaha. I dont have the luxury of a mistake since i cant get good replacement where im from :( . So...
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  14. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    Great ! I got a response from Robo3d that says : " Hi Marcos Try heating and then pushing through with something good and stiff that is close to...
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting
  15. Marcos Zuccaro
    Post

    Solved JAM, filament stuck past heatsink

    can i disassemble the heatsink from the heatbreak without removing the nozzle? or the procedure is nozzle then the heatsink. All of this allways...
    Post by: Marcos Zuccaro, Jun 21, 2017 in forum: Troubleshooting