1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by racer

  1. racer
    Post

    Repurposing Pirate3d Buccaneer

    No don't think so. The error is on the side of your PC. do you see /dev/ttyS5 if you do an ls /dev/ttyS* from the command prompt? What do you...
    Post by: racer, May 10, 2020 in forum: Off Topic
  2. racer
    Post

    Repurposing Pirate3d Buccaneer

    Could it be an access rights issue? Maybe the octoprint user has to be added to the dial-out group? Did you do take the steps below? As root...
    Post by: racer, May 10, 2020 in forum: Off Topic
  3. racer
    Post

    Repurposing Pirate3d Buccaneer

    The standard is the gcode standard. In the Marlin firmware you have defined your printer, and Marlin accepts gcode. I wouldn't recommend slicing...
    Post by: racer, May 9, 2020 in forum: Off Topic
  4. racer
    Post

    Repurposing Pirate3d Buccaneer

    Hi M2T, just saw your post. Indeed I didn't post a make with the Buccaneer, because I made a mistake in the firmware causing the printer to...
    Post by: racer, May 7, 2020 in forum: Off Topic
  5. racer
    Post

    Repurposing Pirate3d Buccaneer

    For those that would like to make the changes to Marlin 2.0 you can use my files. Steps that you need to take to add the BUCCANEER Logic Board...
    Post by: racer, Dec 29, 2019 in forum: Off Topic
  6. racer
    Post

    Repurposing Pirate3d Buccaneer

    **** BREAKING NEWS **** I've got an updated version of the firmware based on Marlin 2.0. It seems to work fine, no more funny resets. I think I...
    Post by: racer, Dec 29, 2019 in forum: Off Topic
  7. racer
    Post

    Repurposing Pirate3d Buccaneer

    You need to install avrdude on the Cubieboard of the buccaneer, transfer the firmware to the Cubieboard and than flash the ATMEL chip from the...
    Post by: racer, Dec 27, 2019 in forum: Off Topic
  8. racer
    Post

    Repurposing Pirate3d Buccaneer

    What I think happens is that the AtMega 1684 resets and that this causes the communication time out. My suspicion is that the reset is caused by a...
    Post by: racer, Feb 28, 2019 in forum: Off Topic
  9. racer
    Post

    Repurposing Pirate3d Buccaneer

    ok, atleast the bug is consistent... I was worried that I might have damaged my printer whilst reverse engineering the pcb with my probes.
    Post by: racer, Feb 27, 2019 in forum: Off Topic
  10. racer
    Post

    Repurposing Pirate3d Buccaneer

    @mobilephase Kindly note that the Marlin configuration still might be buggy, I haven't the time yet to look where the spontaneoous reset comes...
    Post by: racer, Feb 27, 2019 in forum: Off Topic
  11. racer
    Post

    Repurposing Pirate3d Buccaneer

    Ok, thx for the feedback!
    Post by: racer, Jan 28, 2019 in forum: Off Topic
  12. racer
    Post

    Repurposing Pirate3d Buccaneer

    Also I have changed the settings for the thermistor in the Configuration.h file, this is what I use now, after the auto calibration: .... #define...
    Post by: racer, Jan 28, 2019 in forum: Off Topic
  13. racer
    Post

    Repurposing Pirate3d Buccaneer

    Hi Harr, nice to know that there is atleast one other person in this world looking at the Buccaneer 3D printer. I felt a bit lonely after the...
    Post by: racer, Jan 28, 2019 in forum: Off Topic
  14. racer
    Post

    Repurposing Pirate3d Buccaneer

    Buccaneer lighting The lighting of the Buccaneer is managed by an ATTINY1634 mounted on the Buccaneer Logicboard. There are two lightsources, 7...
    Post by: racer, Jan 15, 2019 in forum: Off Topic
  15. racer
    Post

    Repurposing Pirate3d Buccaneer

    I think with all the information & instructions above anyone should be able to give his / her Buccaneer a proper brainwash :). Please contact me...
    Post by: racer, Jan 15, 2019 in forum: Off Topic