1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Robert Foreman

  1. Robert Foreman
    Post

    Answered Dumb question: Nozzle Sizes

    Your Welcome. I have not had time to play with the other sizes yet.
    Post by: Robert Foreman, Oct 25, 2016 in forum: General Questions
  2. Robert Foreman
    Post

    Answered Dumb question: Nozzle Sizes

    I got the fun pack and did a side by side for the .25 and the .4mm to show the detail you can get in the lettering....
    Post by: Robert Foreman, Oct 25, 2016 in forum: General Questions
  3. Robert Foreman
    Post

    What is a safe temp for the stepper motor?

    Thanks guys. The extruder is not the one that came on my Robo. I had to replace it with a spare I had for my Flash Forge Creator Pro. On the FFCP...
    Post by: Robert Foreman, Sep 27, 2016 in forum: General Questions
  4. Robert Foreman
    Thread

    What is a safe temp for the stepper motor?

    What is a good safe temp for the stepper motor. My extruder motor is running around 70c to 74c. Is that too hot or normal?
    Thread by: Robert Foreman, Sep 27, 2016, 4 replies, in forum: General Questions
  5. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    Thanks for the help and direction to look Mark. :)
    Post by: Robert Foreman, Sep 22, 2016 in forum: Troubleshooting
  6. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    Well I adjusted the voltage up to a .65 and it was still doing it. So I tried replacing the motor with a spare I had for my FFCP and now it's...
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  7. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    The one I put in was brand new. Never been used. I have 4 more of those. Should I try to up the voltage to .6?
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  8. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    Well replacing the stepper driver did not work it still doing it. Here is the crazy thing. I can grab the gear on the motor and stop the motor...
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  9. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    Well the kit I have has the A4988 with the adjustment pot on it and as it turns out I have 5 spares for my Flash Forge Creator Pro that are A4988...
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  10. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    ok thanks. Start looking at it a soon as this print is done.
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  11. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    Yes the motor stops but just for a fraction of a second. I will check the stepper drivers after the current print stops. Can I replace the current...
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  12. Robert Foreman
    Post

    Solved Extruder skipping while printing need help.

    As I watch the gears turning I see it stop and then jump forward. It does it while doing the shell but not where a retraction should happen. and...
    Post by: Robert Foreman, Sep 21, 2016 in forum: Troubleshooting
  13. Robert Foreman
    Thread

    Solved Extruder skipping while printing need help.

    My extruder motor just started skipping while printing. What do I need to do to fix it? it had been doing fine till 2 days ago when I noticed...
    Thread by: Robert Foreman, Sep 21, 2016, 17 replies, in forum: Troubleshooting