1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Scifideity

  1. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    If my last attempt at fixing hadn't done the trick and got me back up and running, I was going to do just that. Right after using the current one...
    Post by: Scifideity, Dec 9, 2021 in forum: Troubleshooting
  2. Scifideity
    Post

    Bed replacement on R1 beta

    Thanks. It's a lot of fun. A lot of work too but definitely a lot of fun. :D
    Post by: Scifideity, Dec 9, 2021 in forum: Projects
  3. Scifideity
    Post

    Bed replacement on R1 beta

    Hi @mark tomlinson , Yeah, it does take me almost a month to take/down and pack up Halloween ;) This was my 20th Annual Yard Haunt so I had a...
    Post by: Scifideity, Dec 9, 2021 in forum: Projects
  4. Scifideity
    Post

    Bed replacement on R1 beta

    Hi Mark, Sorry for the delay. Had to walk away from the printer issues for a bit and focus on Halloween Yard Haunt prep and setup. I'll be...
    Post by: Scifideity, Nov 3, 2021 in forum: Projects
  5. Scifideity
    Post

    Bed replacement on R1 beta

    Hi @mark tomlinson Wiring for this Heat Sinked MOSFET seems pretty straight forward but wanted to double check just in case. I just got one of...
    Post by: Scifideity, Oct 21, 2021 in forum: Projects
  6. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    I'll give that one a try. Amazon claims it can be here tomorrow but I'll believe that when I see it on my front porch /LOL j Thanks
    Post by: Scifideity, Oct 18, 2021 in forum: Troubleshooting
  7. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Does that SSR look sufficient? When I order another one should I get a different set of specs?
    Post by: Scifideity, Oct 18, 2021 in forum: Troubleshooting
  8. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Got it via Amazon https://www.amazon.com/gp/product/B08FQWB8HJ/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 According to the other threads it...
    Post by: Scifideity, Oct 18, 2021 in forum: Troubleshooting
  9. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Looks like the problem is the SSR. Took the SSR out of the picture and the Bed starts heating up right away. I checked the voltages both with...
    Post by: Scifideity, Oct 17, 2021 in forum: Troubleshooting
  10. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    When it wouldn't do the PID Tuning I tried setting it for a print and the hot end started getting up to temp but the bed never read more than room...
    Post by: Scifideity, Oct 17, 2021 in forum: Troubleshooting
  11. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Whelp. It wasn't the RAMPS. Put the new one in and same issue with the LCD. Pulled off the stepper drivers and swapped them a new set and the...
    Post by: Scifideity, Oct 16, 2021 in forum: Troubleshooting
  12. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    Yup, I have the second one and double checked my firmware just to be sure. [ATTACH] [ATTACH] This is the same firmware file I used...
    Post by: Scifideity, Oct 16, 2021 in forum: Troubleshooting
  13. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    I have the cables labeled so I don't get them mixed up but flipped them to make sure the positions didn't change with this non-Robo RAMPS board....
    Post by: Scifideity, Oct 15, 2021 in forum: Troubleshooting
  14. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    I just went through the SSR thread and got one installed. [ATTACH] I had ordered another kit "just in case" so I swapped out everything again...
    Post by: Scifideity, Oct 13, 2021 in forum: Troubleshooting
  15. Scifideity
    Post

    Solved At my wits end. Need help w/ firmware

    SSR arrived today so I went to work it into the system and noticed this. YIKES!! Had to cut two of the PSU wires to get the RAMPS out of the...
    Post by: Scifideity, Oct 13, 2021 in forum: Troubleshooting