1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Spidematt

  1. Spidematt
    Thread

    Having issues verifying arduino firmwares

    I am deep into rebuilding my robo3d added a bl touch and every one of the firmware files in the forums will not verify through arduino gives me...
    Thread by: Spidematt, Sep 28, 2019, 2 replies, in forum: Mods and Upgrades
  2. Spidematt
    Post

    Anyone install a BLtouch on their robo?

    Did you get bltouch to work and was it just a drop in I am thinking of going this route it seems like it would just replace endstop switches and work
    Post by: Spidematt, Mar 28, 2017 in forum: Mods and Upgrades
  3. Spidematt
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    i got offset to work through simplify. is there any changes i need to make to start gcode im just using simplify3d default robo3d gcode
    Post by: Spidematt, Mar 26, 2017 in forum: Mods and Upgrades
  4. Spidematt
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I found it and just moved the // from one to the other and it works now thanks for youre help that was fast . only other issue i have now is M851...
    Post by: Spidematt, Mar 26, 2017 in forum: Mods and Upgrades
  5. Spidematt
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    trying all this out however cant get anything to show up on my reprap discount xxl lcd using this
    Post by: Spidematt, Mar 26, 2017 in forum: Mods and Upgrades
  6. Spidematt
    Post

    Verticle rod and toranado

    The 14 is alot smaller you could make a 17 work if you drilled new holes which might be better cause the nema 14 is very hot to touch even with...
    Post by: Spidematt, Mar 8, 2017 in forum: Mods and Upgrades
  7. Spidematt
    Post

    Verticle rod and toranado

    I printed at 85 % on everything the fastest i print at is infill and I print at 60 the robo has a real heavy build plate so not alot we can do...
    Post by: Spidematt, Mar 8, 2017 in forum: Mods and Upgrades
  8. Spidematt
    Post

    Verticle rod and toranado

    Yea with a normal i3 extruder you might be able to get away with the middle rods I'll double check make sure the file is updated for the in...
    Post by: Spidematt, Mar 6, 2017 in forum: Mods and Upgrades
  9. Spidematt
    Post

    Verticle rod and toranado

    http://www.thingiverse.com/thing:1246951 http://www.thingiverse.com/thing:2022223 Use the one labeled robo toranado v3 the other one works but it...
    Post by: Spidematt, Mar 5, 2017 in forum: Mods and Upgrades
  10. Spidematt
    Post

    Verticle rod and toranado

    the toranado is almost half the weight of the stock carriage
    Post by: Spidematt, Mar 5, 2017 in forum: Mods and Upgrades
  11. Spidematt
    Thread

    Verticle rod and toranado

    This seems to be working very well right now the toranado extruder is nice.[ATTACH]
    Thread by: Spidematt, Mar 4, 2017, 26 replies, in forum: Mods and Upgrades
  12. Spidematt
    Thread

    Robonado X

    Ok finally got it mostly finished just need some tuning but it works pretty good might even try a normal prusa extruder setup[ATTACH]
    Thread by: Spidematt, Mar 2, 2017, 0 replies, in forum: Projects