1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Sylva

  1. Sylva
    Post

    Solved Z-Axis not responding.

    Tested the homing after uploading the firmware you linked and works great now! Thank you guys for your help! I now have both printers working great.
    Post by: Sylva, Dec 31, 2017 in forum: Troubleshooting
  2. Sylva
    Post

    Solved Z-Axis not responding.

    Thanks, I trying uploading the r1plus firmware you hotlinkd, and Im getting this error. I didn't change anything to it yet. just opened and hit...
    Post by: Sylva, Dec 30, 2017 in forum: Troubleshooting
  3. Sylva
    Post

    Solved Z-Axis not responding.

    I don't remember the site I got it from but when I go to download it from the robo limk, the site 404s Sent from my SM-G930V using Tapatalk
    Post by: Sylva, Dec 30, 2017 in forum: Troubleshooting
  4. Sylva
    Post

    Solved Z-Axis not responding.

    I ruled out the stepper driver, the ramps ( swapped with a board from my parts robo), stepper motor works fine when I plugged it in as my y-axis....
    Post by: Sylva, Dec 29, 2017 in forum: Troubleshooting
  5. Sylva
    Post

    Solved Z-Axis not responding.

    So, I tried every possible mechanical fix and still to cannot seem to get the issue fixed. ALTHOUGH, with that said, I decided to make an all or...
    Post by: Sylva, Dec 29, 2017 in forum: Troubleshooting
  6. Sylva
    Post

    Solved Z-Axis not responding.

    Nope, not the driver and I can turn the z rods with ease. This is the bootup, not sure if anything seems off about it. Attempting connection at...
    Post by: Sylva, Dec 20, 2017 in forum: Troubleshooting
  7. Sylva
    Post

    Solved Z-Axis not responding.

    Swapping the drivers now, thankfully I bought a bunch to build an extended 3dmax in a month but anyway, swapping driver now.
    Post by: Sylva, Dec 20, 2017 in forum: Troubleshooting
  8. Sylva
    Post

    Solved Z-Axis not responding.

    READ: Reporting endstop status READ: x_min: TRIGGERED READ: y_min: TRIGGERED READ: z_min: open READ: ok SENT: M105 READ: ok T:20.5 /0.0...
    Post by: Sylva, Dec 20, 2017 in forum: Troubleshooting
  9. Sylva
    Post

    Solved Z-Axis not responding.

    Do it should be normally closed for mine? Sent from my SM-G930V using Tapatalk
    Post by: Sylva, Dec 19, 2017 in forum: Troubleshooting
  10. Sylva
    Post

    Solved Z-Axis not responding.

    So as it sits rested is open. Lifted off reads triggered. Sent from my SM-G930V using Tapatalk
    Post by: Sylva, Dec 18, 2017 in forum: Troubleshooting
  11. Sylva
    Post

    Solved Z-Axis not responding.

    I believe the firmware is the r1+. Here are the pictures of the ramps hookup[IMG][IMG][IMG] Sent from my SM-G930V using Tapatalk
    Post by: Sylva, Dec 18, 2017 in forum: Troubleshooting
  12. Sylva
    Post

    Solved Z-Axis not responding.

    Nope connected them correctly.[IMG][IMG] Sent from my SM-G930V using Tapatalk
    Post by: Sylva, Dec 18, 2017 in forum: Troubleshooting
  13. Sylva
    Thread

    Solved Z-Axis not responding.

    Hey all, It's me again, I have been trying to figure out why my z-axis is still not responding. I wired the endstops into and go to press home...
    Thread by: Sylva, Dec 18, 2017, 26 replies, in forum: Troubleshooting
  14. Sylva
    Post

    Solved X-Axis Homing Reversed?

    I traced it and the wiring was cut at that splice. Do I have to resplice the wiring or are there premade splitter endstop wires I can get? Sent...
    Post by: Sylva, Nov 22, 2017 in forum: Troubleshooting