1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Terrell Grant

  1. Terrell Grant
    Post

    Unanswered X axis not homing properly

    Maybe this will help clear up the problem. The manual x controls work, however, when I try to home it, it just moves a little to the x+ direction....
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  2. Terrell Grant
    Post

    Unanswered X axis not homing properly

    uninstalled and reinstalled matter control same. I didn't think that would work because again sometime it homes. I even tried to load it for my...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  3. Terrell Grant
    Post

    Unanswered X axis not homing properly

    Yes its tight. If I move the belt by hand the head moves too. Should I post a new video? I'm not sure what a slicer is. Matter Control version...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  4. Terrell Grant
    Post

    Unanswered X axis not homing properly

    My X axis does not read home. If I am on Matter Control and I jog X to the center of the board, then click Home X, it moves to the opposite...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  5. Terrell Grant
    Post

    Unanswered X axis not homing properly

    When you watch the original video, when the X has to go back towards home, why doesn't the Z allow time for the X to travel? As soon as the Z goes...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  6. Terrell Grant
    Post

    Unanswered X axis not homing properly

    I just tried changing my USB cable just to see if that my fix it. Still the same.
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  7. Terrell Grant
    Post

    Unanswered X axis not homing properly

    Just to be clear because I had a typo. My switch is reading closed until the switch is pressed same as your. I also try to wire it open until...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  8. Terrell Grant
    Post

    Unanswered X axis not homing properly

    If you look at the picture of the switch I posted. I tried moving the black wire to the open terminal. Because that is always closed until the...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  9. Terrell Grant
    Post

    Unanswered X axis not homing properly

    When I try to home the X axis it moves the X about 10mm in the wrong direction. Again this doesn't happen every time. However I'm not sure how...
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  10. Terrell Grant
    Post

    Unanswered X axis not homing properly

    When the switch is pressed it shows that the switch is closed. When not press it show open
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  11. Terrell Grant
    Post

    Unanswered X axis not homing properly

    I tried to move the plug to the other terminals on the switch. Still didn't work.
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  12. Terrell Grant
    Post

    Unanswered X axis not homing properly

    I metered the switch and when I put the terminals on the switch it reads that it is on all the time, and when the switch is pressed it turns off....
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  13. Terrell Grant
    Post

    Unanswered X axis not homing properly

    Remember, it doesnt do it all the time.
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  14. Terrell Grant
    Post

    Unanswered X axis not homing properly

    Switch is connected firmly. Is there any way to test the connection to my switch to make sure its working? Could this be my problem?
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting
  15. Terrell Grant
    Post

    Unanswered X axis not homing properly

    Yes, but it doesnt always home to the switch.Even if I push the dog switch in for it to stop, i can still move it in mattercontrol.
    Post by: Terrell Grant, Mar 22, 2016 in forum: Troubleshooting