1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Twofirstnames

  1. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Hi Geof, Thanks for checking in on me. I haven't had much time the last couple weeks to mess with this (decided I was super bored so I would...
    Post by: Twofirstnames, Aug 30, 2017 in forum: Troubleshooting
  2. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Thanks. I'll track them again. Danzca posted a great reference video. I'll follow that again to double check. I don't have a meter, but am going...
    Post by: Twofirstnames, Aug 20, 2017 in forum: Troubleshooting
  3. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Ok, folks. Need some more advice. I tried this morning to heat the extruder as Mark suggested, but it won't heat up. I'm still getting the...
    Post by: Twofirstnames, Aug 20, 2017 in forum: Troubleshooting
  4. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Thanks. I'll give that a shot tomorrow. Sent from my Nexus 6P using Tapatalk
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  5. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    yes, yes it is definately gummed up...... see picture :-)
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  6. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Hi Mark, Here is a picture of the head after I finally figured out how to get it off. I see no locking screws and it won't just pull out. Is...
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  7. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    And here are the wiring photos with the new R1+ bed instead of the original R1. PS. That's the original Arduino and RAMPS board. Not the new one...
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  8. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    [ATTACH] [ATTACH] [ATTACH] Ok guys. I finally got a chance to snap some pictures. Here are the print head shots. Sorry for the dirty...
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  9. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Thanks Mark. I just uploaded the ROBO3DRV1V3_06112015 using Arduino. I'm with you that this is likely the correct version.
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  10. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Thanks, will try to get some pictures up this evening. (fingers crossed)
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  11. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    That will likely be in the future. LOL Right now my focus is just getting this printing again. I'd love to play around with code someday,...
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  12. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Fantastic! Thanks for that breakdown. I wasn't sure the difference between the 5\16 and the 8mm. It is apparent, based on your breakdown that I...
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  13. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Thanks Mark, That is where I got the files to upload. I just uploaded the correct version as you suggested. Thanks for the clarification. I...
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  14. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    I have the R1 (not the R1+). I will try to get some pictures uploaded this evening. Been working in the yard most of the day today.
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting
  15. Twofirstnames
    Post

    Partial Answer Warming Bed Issues (Am I on the right track)

    Thanks, I'll try to see if I can get the print head off. I'll also upload some pictures if I can.
    Post by: Twofirstnames, Aug 19, 2017 in forum: Troubleshooting