1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Will . I . Am

  1. Will . I . Am
    Post

    Community Favorite Mike Kelly's RoBo3D Enclosure

    @Todd Wessendorf do you happened to have the measurements of the pieces cut? like the ones with the clear plastic so you can see etc...
    Post by: Will . I . Am, May 24, 2017 in forum: Mods and Upgrades
  2. Will . I . Am
    Post

    Answered Filament/print head grabbing extruded filament off of bed

    @WheresWaldo So in other words try setting my first layer height to a 0.2 vs 0.3? I normally like to print at 0.2 layer height resolution as...
    Post by: Will . I . Am, Apr 18, 2017 in forum: Troubleshooting
  3. Will . I . Am
    Post

    Answered Filament/print head grabbing extruded filament off of bed

    @mark tomlinson So printed new design this time at 198 hot end and print bed at 48 but as you can see this made a HUGE glob of filament once it...
    Post by: Will . I . Am, Apr 17, 2017 in forum: Troubleshooting
  4. Will . I . Am
    Post

    Answered Top layer gaps/missing layer?

    @mark tomlinson I'm at 30% infill overlap right now. Should i try going higher? Also is 50 bed temp?
    Post by: Will . I . Am, Apr 17, 2017 in forum: Troubleshooting
  5. Will . I . Am
    Post

    Answered Top layer gaps/missing layer?

    @mark tomlinson 7-9 were much better but what i want to know is are the faint lines on top normal for prints?
    Post by: Will . I . Am, Apr 17, 2017 in forum: Troubleshooting
  6. Will . I . Am
    Post

    Answered Filament/print head grabbing extruded filament off of bed

    @mark tomlinson wel i got the -1.0 issue resolved and that seems to have helped. So ill try the heat to maybe 195 and see what happens. Again you...
    Post by: Will . I . Am, Apr 17, 2017 in forum: Troubleshooting
  7. Will . I . Am
    Thread

    Answered Top layer gaps/missing layer?

    So I'm printing with CURA now and I seems to no matter what I try so far keep getting the tops of my prints to have gaps or lines so it's not a...
    Thread by: Will . I . Am, Apr 17, 2017, 5 replies, in forum: Troubleshooting
  8. Will . I . Am
    Post

    Answered Filament/print head grabbing extruded filament off of bed

    Tuned to -1.0 z offset and helped but now it curls up sort of on sides [IMG] Sent from my iPhone using Tapatalk
    Post by: Will . I . Am, Apr 17, 2017 in forum: Troubleshooting
  9. Will . I . Am
    Thread

    Answered Filament/print head grabbing extruded filament off of bed

    So every time I print now my ROBO 3D R1 plus seems to all most grab the filament and just make a mess right after it starts to print the skirt....
    Thread by: Will . I . Am, Apr 17, 2017, 10 replies, in forum: Troubleshooting
  10. Will . I . Am
    Post

    Solved HELP!! Stepper motors only going up not down!

    GOT IT!!!! Thanks so much for the help! I thought i ruined my Robo forever! :)
    Post by: Will . I . Am, Apr 16, 2017 in forum: Troubleshooting
  11. Will . I . Am
    Post

    Solved HELP!! Stepper motors only going up not down!

    ok now i see! its not supposed to be that low! But damm how on earth did it manage to bump it that far out of proportion wow.
    Post by: Will . I . Am, Apr 16, 2017 in forum: Troubleshooting
  12. Will . I . Am
    Post

    Solved HELP!! Stepper motors only going up not down!

    @mark tomlinson well the rod on the left side I adjusted till i hard a clicking sound so its touching but the one on the right side where theres...
    Post by: Will . I . Am, Apr 16, 2017 in forum: Troubleshooting
  13. Will . I . Am
    Post

    Solved HELP!! Stepper motors only going up not down!

    also @mark tomlinson Where are the Z switches located? are the one of the pictures pictured above? Or are they somewhere below where you can't see...
    Post by: Will . I . Am, Apr 16, 2017 in forum: Troubleshooting