1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Partial Answer Every print comes out crooked

Discussion in 'Troubleshooting' started by gunsmoke132, Jul 8, 2017.

  1. gunsmoke132

    gunsmoke132 Member

    Joined:
    May 13, 2016
    Messages:
    183
    Likes Received:
    14
    I have been trying to print out a sprocket and it prints out as if the bed was at an angle. I've tried homing all axis wit G28 command but with no avail. Idk how to fix this or what could be causing this
     
    #1 gunsmoke132, Jul 8, 2017
  2. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,914
    Likes Received:
    7,338
    Well... without any information at all ... we probably can't come up with ideas :)
    If this is a beta your bed needs better leveling... start fiddling with the adjustment screws.
     
    #2 mark tomlinson, Jul 8, 2017
  3. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,914
    Likes Received:
    7,338
    Also some details about which printer you are using would be really important.
    How you solve problems totally depends on which one.
     
    #3 mark tomlinson, Jul 8, 2017
  4. gunsmoke132

    gunsmoke132 Member

    Joined:
    May 13, 2016
    Messages:
    183
    Likes Received:
    14
    I'll add a picture
     
    #4 gunsmoke132, Jul 8, 2017
  5. gunsmoke132

    gunsmoke132 Member

    Joined:
    May 13, 2016
    Messages:
    183
    Likes Received:
    14
    unnamed.jpg
     
    #5 gunsmoke132, Jul 8, 2017
  6. gunsmoke132

    gunsmoke132 Member

    Joined:
    May 13, 2016
    Messages:
    183
    Likes Received:
    14
    #6 gunsmoke132, Jul 8, 2017
  7. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,914
    Likes Received:
    7,338
    Looks to be a little over extrusion and the auto leveling is not working exactly correctly.
    Both of those comments are predicated on another assumption (since you didn't tell us) that this is PLA filament.

    To get the auto leveling adjusted I suggest you do two things.
    1) Make sure the Z switches and mounts are both mounted in exactly the same position on both sides.
    2) Review the first video here: http://community.robo3d.com/index.php?threads/helpful-videos-novice-expert.7478/
     
    #7 mark tomlinson, Jul 8, 2017
  8. gunsmoke132

    gunsmoke132 Member

    Joined:
    May 13, 2016
    Messages:
    183
    Likes Received:
    14
    Honestly I think it's the PEI sheet that I put on there I think it's starting to bubble
     
    #8 gunsmoke132, Jul 8, 2017
  9. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,914
    Likes Received:
    7,338
    That would totally do it too :)
     
    #9 mark tomlinson, Jul 8, 2017

Share This Page