1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Shigemal
    Post

    Solved Printing shows Z offset

    [IMG] good night robo, please let me know good result
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  2. Shigemal
    Post

    Solved Printing shows Z offset

    [IMG] Good enough thickness on this print.
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  3. Shigemal
    Post

    Solved Printing shows Z offset

    Autolevel calibration has been perfomed with monitor switch by ohm meter as sound. Mattercontrol zaxis elevation after Z endstop. My case offset...
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  4. Shigemal
    Post

    Solved Printing shows Z offset

    And today I have changed ultralcd.cpp for handle minus z offset value.
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  5. Shigemal
    Post

    Solved Printing shows Z offset

    I am using Robo3D firmware Auto_level_7_17_8mm from robo site. And added some changes for titan.
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  6. Shigemal
    Post

    Solved Printing shows Z offset

    [IMG] now printing will start
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  7. Shigemal
    Post

    Solved Printing shows Z offset

    I am looking into marlin code, so far handling minus value is most likely new issue on this code. I have changed ultralcd.cpp as following and...
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  8. Shigemal
    Post

    Solved Printing shows Z offset

    Thanks Mark I have reviewed thread of M565 issue . And negative z-offset of Robo3D mechanism is unique. regards
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  9. Shigemal
    Post

    Solved Printing shows Z offset

    I had tried to change z offset parameter on start gcode script. from Z-0.6 into Z-1.5 and result shows better Sorry for make confusion, I had...
    Post by: Shigemal, Sep 6, 2016 in forum: Troubleshooting
  10. Shigemal
    Post

    Solved Printing shows Z offset

    [IMG] Try result with M565 Z-1.5 shows better result (1.7mm) It is propagated from Z offset setting But caliblation result may not shows such...
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  11. Shigemal
    Post

    Solved Printing shows Z offset

    My slicer is mattercontrol set . And it is performed through SD card bases.
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  12. Shigemal
    Post

    Solved Printing shows Z offset

    Dear danzca6 Yes original design has stood up. But screw style of printing at Robo3D y-axis movement factor makes worse for it. I have another 3D...
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  13. Shigemal
    Post

    Solved Printing shows Z offset

    Dear danzca6 Z-e step may not have issue because top side print layer is correct. You can see it on black one (past) and yellow one (current)....
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  14. Shigemal
    Post

    Solved Printing shows Z offset

    [ATTACH] Gcode may have right layer but printer does not output in place
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  15. Shigemal
    Post

    Solved Printing shows Z offset

    Yes bottom few layers are missing
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  16. Shigemal
    Post

    Solved Printing shows Z offset

    [IMG] Black one was created in before printer update. It was printer update on extruder so titan need to update marlin firmware for extruder step...
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  17. Shigemal
    Post

    Solved Printing shows Z offset

    [IMG] I had cancelled print because behavior shows on bottom as before.
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  18. Shigemal
    Post

    Solved Printing shows Z offset

    My start gcode setting is following. G28 X0 Y0 Z0 ; home all axes G1 Z5 F5000 ; lift nozzle M109 S[temperature] ; set the extruder temp and wait...
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  19. Shigemal
    Post

    Solved Printing shows Z offset

    Thanks Danzca6 It is printing parts screw of http://www.thingiverse.com/thing:1551236. So problem is on bottom side, this screw has been created...
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
  20. Shigemal
    Post

    Solved Printing shows Z offset

    I am trying to confirm print again with right setting that makes new gcode for it. Using Mattercontrol with viewing start gcode script with...
    Post by: Shigemal, Sep 5, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 36 Next >
Search Again
Page 1 of 2