1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 10 of 10
  1. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Yeah I know. Probably just bad timing. Believe it or not I've spent almost 1100 euros getting this printer to a point where it almost works to an...
    Post by: Oisin, Aug 18, 2016 in forum: Mods and Upgrades
  2. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Aaaand my PSU has stopped working. Damn. Looks like no more testing for me until I can figure out what happened.
    Post by: Oisin, Aug 18, 2016 in forum: Mods and Upgrades
  3. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    I haven't tried that but I will. It just failed a print and when I restarted, the z-values for the autolevelling sequence were very different to...
    Post by: Oisin, Aug 18, 2016 in forum: Mods and Upgrades
  4. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Positive brings me too far above the bed. Negative brings me closer. I'm not sure why it's -1.85. That just seems to be the number that puts me...
    Post by: Oisin, Aug 18, 2016 in forum: Mods and Upgrades
  5. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    So I did the test with a cube in each corner. Had to turn on the heated bed to get the top right cube to stick down. I posted pictures of the...
    Post by: Oisin, Aug 18, 2016 in forum: Mods and Upgrades
  6. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Ok. It's pretty late here now so tomorrow I'm going to put a test cube in each corner and test to see if the first layers are all pretty even....
    Post by: Oisin, Aug 17, 2016 in forum: Mods and Upgrades
  7. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Nope. I'm using the black side. Getting different z values every autolevel shouldn't make a difference should it? Wouldn't my z-offset screw it...
    Post by: Oisin, Aug 17, 2016 in forum: Mods and Upgrades
  8. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    The printers old Autolevel technique never helped me at all. This is some revolutionary stuff! Jim really built something outstanding. Thanks very...
    Post by: Oisin, Aug 17, 2016 in forum: Mods and Upgrades
  9. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Good call. I was doing that as you typed! Seems to have produced a better result: READ: Bed x: 35.00 y: 20.00 z: -0.01 READ: Bed x: 120.00 y:...
    Post by: Oisin, Aug 17, 2016 in forum: Mods and Upgrades
  10. Oisin
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    I did it and noticed a difference left to right rather than right to left. I tried deliberately making an obvious slant so that the left side was...
    Post by: Oisin, Aug 17, 2016 in forum: Mods and Upgrades
Find older messages
Showing results 181 to 190 of 190
Search Again
Page 10 of 10