1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 5
  1. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    I see what I did wrong. Thank you WhereWaldo!
    Post by: Cbrown, Mar 31, 2016 in forum: Show and Tell
  2. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    I didn't change my offsets the first time and when the printer probed after heating it went right through the plate and made a hole.
    Post by: Cbrown, Mar 31, 2016 in forum: Show and Tell
  3. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    I haven't had a problem with bowing on my after a few months of use. They recommend using little to no heat to make sure the plate doesn't bend or...
    Post by: Cbrown, Mar 28, 2016 in forum: Show and Tell
  4. Cbrown
    Post

    Zebra Skin - build surface

    Oh that makes sense.
    Post by: Cbrown, Mar 28, 2016 in forum: Off Topic
  5. Cbrown
    Post

    Zebra Skin - build surface

    According to their website it was $56.
    Post by: Cbrown, Mar 28, 2016 in forum: Off Topic
  6. Cbrown
    Post

    Build Plates - Are they all the same?

    Yeah that the good thing about the Robo, everything is pretty well concealed. Ill have to give it a try.
    Post by: Cbrown, Mar 28, 2016 in forum: Mods and Upgrades
  7. Cbrown
    Post

    Build Plates - Are they all the same?

    Over spray and getting it on the electronics
    Post by: Cbrown, Mar 28, 2016 in forum: Mods and Upgrades
  8. Cbrown
    Thread

    BuildTak - Is it worth the money?

    BuildTak Price: $4.00 to $21.00 depending on size and quality Specs: 4.5″ x 4.5″ (114*114), 6.5″ x 6.5″ (165*165), 6.5″ Diameter (165Dia),...
    Thread by: Cbrown, Mar 28, 2016, 0 replies, in forum: Off Topic
  9. Cbrown
    Post

    Zebra Skin - build surface

    Is kind of expensive for the 10 x 10. I looked at them yesterday.
    Post by: Cbrown, Mar 28, 2016 in forum: Off Topic
  10. Cbrown
    Post

    Build Plates - Are they all the same?

    I have never used hair spray on any of my printers. I am just nervous about it for some reason.
    Post by: Cbrown, Mar 28, 2016 in forum: Mods and Upgrades
  11. Cbrown
    Post

    Build Plates - Are they all the same?

    *** I stated above that the temperature used was 15c. This was the temperature typed into the slicer. This doesn't account for ambient heat or...
    Post by: Cbrown, Mar 27, 2016 in forum: Mods and Upgrades
  12. Cbrown
    Thread

    Build Plates - Are they all the same?

    BuildTak / Fleks3d / Proto-Pasta Product Review BuildTak Price: $4.00 to $21.00 depending on size and quality Specs: 4.5″ x 4.5″ (114*114),...
    Thread by: Cbrown, Mar 27, 2016, 16 replies, in forum: Mods and Upgrades
  13. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    Just make sure to be careful when you calibrate so you don't burn a hole in the plate with the nozzle. I did on mine :(
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  14. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    I apologize for getting unruly
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  15. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    Kind of did. The last line of the sheet they send out reads, "...do not require a heated bed." and "If used with heated beds, we suggest keeping...
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  16. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    B. I never said it stuck at 15c. I said and I quote, "The degree in celsius I put in was 15." For the record, "Green" doesn't mean anything. I am...
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  17. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    I understand what you are saying about ambient heat. I have attached the sheet that actually comes with the Fleks3d be. I suggest you read it and...
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  18. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    OOOh I see what you are saying. What it was physically at I don't know. The degree in celsius I put in was 15c.
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  19. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    I'm sorry I don't know what you are saying here. One of the first prints I did when I tested Fleks3d I set the build plate at 15c, because I was...
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
  20. Cbrown
    Post

    First test of FLEKS 3D build plate kit

    @KTMDirtFace Yes, Fleks3d works with ABS. I print ABS on the plate with about 15c heat. @Archania Also look into Proto-Pasta's build plate. You...
    Post by: Cbrown, Mar 26, 2016 in forum: Show and Tell
Showing results 61 to 80 of 94 Next >
Search Again
Page 4 of 5