1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Perry Genovese
    Post

    Solved Terribly Inconsistent Printer!

    to get my bed level was a nightmare. I use a depth gage on my digital caliper. I use the horizontal rod of the x-axis with the bed centered...
    Post by: Perry Genovese, Feb 22, 2017 in forum: Troubleshooting
  2. Perry Genovese
    Post

    Solved Extruder Stepper Problems

    Final point .... the black wire broke at the plug connection pin at the stepper motor and the insulation was holding it in place
    Post by: Perry Genovese, Feb 15, 2017 in forum: Troubleshooting
  3. Perry Genovese
    Post

    Solved Extruder Stepper Problems

    Ah geez,,,,sorry about this....cable is the cuplrit and it was even mentioned in the other thread I borrowed the video from! I tried the existing...
    Post by: Perry Genovese, Feb 15, 2017 in forum: Troubleshooting
  4. Perry Genovese
    Thread

    Solved Extruder Stepper Problems

    I found this attached video from another thread that was Resolved so I couldn't respond to it...and I didn't see a resolution...but I found my...
    Thread by: Perry Genovese, Feb 15, 2017, 3 replies, in forum: Troubleshooting
  5. Perry Genovese
    Post

    Partially Solved broken bed fix?

    probably but then you have all the sharp edges to deal with :) The kit is $13 I think and there's enough resin in there for multiple repairs.
    Post by: Perry Genovese, Feb 11, 2017 in forum: Troubleshooting
  6. Perry Genovese
    Post

    Partially Solved broken bed fix?

    don't use plastic....you might bury the nozzle in it if its hot during leveling routine. I have fixed chips using windshield repair kit from...
    Post by: Perry Genovese, Feb 11, 2017 in forum: Troubleshooting
  7. Perry Genovese
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    even under rated I find it hard to believe a 100A SSR melted down....I mean those who took them apart noted they were well built but the...
    Post by: Perry Genovese, Feb 7, 2017 in forum: Mods and Upgrades
  8. Perry Genovese
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    is the bottom right corner of the label beveled or square?
    Post by: Perry Genovese, Feb 6, 2017 in forum: Mods and Upgrades
  9. Perry Genovese
    Post

    Partial Answer Weird ripple on some corners of print

    what if you turn your print 90 degrees.....where does that ripple go? Might help you pinpoint which axis is the issue but yeah I have had it as...
    Post by: Perry Genovese, Feb 4, 2017 in forum: Troubleshooting
  10. Perry Genovese
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    It's the same
    Post by: Perry Genovese, Feb 3, 2017 in forum: Mods and Upgrades
  11. Perry Genovese
    Post

    Partial Answer Printing extra strands

    personally I would go hotter. Those are each end of layer strings as it moves to the next location repeatedly layer after layer. Hotter may snap...
    Post by: Perry Genovese, Feb 3, 2017 in forum: Troubleshooting
  12. Perry Genovese
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    FWIW I went with a 400W PSU here https://www.amazon.com/uxcell-AC110V-Switch-Supply-Driver/dp/B019RNKOK6 This was the 1st change I made and for...
    Post by: Perry Genovese, Jan 24, 2017 in forum: Mods and Upgrades
  13. Perry Genovese
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    I got mine from UXCELL on Amazon. The Fotek showed up instead of whats pictured but at least its real...
    Post by: Perry Genovese, Jan 24, 2017 in forum: Mods and Upgrades
  14. Perry Genovese
    Post

    Just got E3Dv6 but have an issue

    i just did the E3DV6 .... you can leave it as PLA in fact. When set up with proper cooling that part of the hot end is cold anyhow. I can hold...
    Post by: Perry Genovese, Jan 21, 2017 in forum: Mods and Upgrades
  15. Perry Genovese
    Thread

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    I'm going to provide a write up with some pics of this conversion I did earlier today. Its really easy and has some benefits. Why am I doing it?...
    Thread by: Perry Genovese, Jan 20, 2017, 92 replies, in forum: Mods and Upgrades
  16. Perry Genovese
    Post

    Solved Power Supply or Arduino?

    awesome...I shall do it this weekend!
    Post by: Perry Genovese, Jan 18, 2017 in forum: Troubleshooting
  17. Perry Genovese
    Post

    Solved Power Supply or Arduino?

    so starting here remove // from the 1st line and then plug in the results from auto tune into the default lines of the 2nd section below also...
    Post by: Perry Genovese, Jan 18, 2017 in forum: Troubleshooting
  18. Perry Genovese
    Post

    Solved Power Supply or Arduino?

    yeah I get the relay and know the difference there don;t worry. I'm more of a dummy with code nuances. Got it on the matter control...
    Post by: Perry Genovese, Jan 18, 2017 in forum: Troubleshooting
  19. Perry Genovese
    Post

    Solved Power Supply or Arduino?

    so this does seem pretty easy. Relay is a piece of cake. As usual finding resources for the code drives me nuts. If I understand it correctly...
    Post by: Perry Genovese, Jan 18, 2017 in forum: Troubleshooting
  20. Perry Genovese
    Post

    Solved Power Supply or Arduino?

    Any write-ups out there guys on this?
    Post by: Perry Genovese, Jan 18, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 43 Next >
Search Again
Page 1 of 3