1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Will Marlin 2.0 work with the stock r1+ Android circuit board?
    Post by: 3dfun4me, Jan 9, 2019 in forum: Mods and Upgrades
  2. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    My last message kind of made it sound like I was putting down Marlin and that is absolutely not what I was trying to say. You all have been a...
    Post by: 3dfun4me, Jan 2, 2019 in forum: Mods and Upgrades
  3. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Ding ding ding! I think we have a winner! I gave up on Cura because of the horizontal rails going out of adjustment, and I went to Slic3r and my...
    Post by: 3dfun4me, Jan 1, 2019 in forum: Mods and Upgrades
  4. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    The ZIP! could have just been acceleration, it startled me with the sound however. The horizontal crossbars never went out of alignment so I don't...
    Post by: 3dfun4me, Dec 28, 2018 in forum: Mods and Upgrades
  5. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Well.... I installed 1.1.9 and after the extruder reaches temperature, the z axis does a little up and down jig that ends with a ZZIIPP!! sound...
    Post by: 3dfun4me, Dec 24, 2018 in forum: Mods and Upgrades
  6. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    I am going to wait to hear back from Bradf80 before i upgrade past 1.1.1 mesh.
    Post by: 3dfun4me, Nov 11, 2018 in forum: Mods and Upgrades
  7. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Would the 1.1.9 be the last update of the 16 bit firmware? And therefore would be the final firmware update to the r1+ because its arduino is...
    Post by: 3dfun4me, Nov 10, 2018 in forum: Mods and Upgrades
  8. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    M851 Z-1.65 looks awfully suspicious. How about M851 Z1.2 Instead.
    Post by: 3dfun4me, Nov 6, 2018 in forum: Mods and Upgrades
  9. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    This is not a problem that I have had. I wonder if setting the number to something different would help. Not sure if that number should be...
    Post by: 3dfun4me, Nov 5, 2018 in forum: Mods and Upgrades
  10. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    How high from the bed does it print?
    Post by: 3dfun4me, Nov 5, 2018 in forum: Mods and Upgrades
  11. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    M851 by itself is just querying the z height from eeprom for your terminal to see, try M851 Z.08 to actually set z height. After that, I got nuthin'.
    Post by: 3dfun4me, Nov 5, 2018 in forum: Mods and Upgrades
  12. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Ps.... CAPS ONLY FOR ALL COMMANDS, my terminal program converts lower case to upper case and it makes me lazy.
    Post by: 3dfun4me, Nov 5, 2018 in forum: Mods and Upgrades
  13. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Forgot that m565 was phased out. I still think that your slicer is adding it's own code to set the Z and it is overriding yours. Check your gcode...
    Post by: 3dfun4me, Nov 5, 2018 in forum: Mods and Upgrades
  14. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    Put the prefix in manually... community.robo3d.com/index.php?threads/revamped-m565-z-offset-set-it-and-forget-it.4748/ You can query M565 to...
    Post by: 3dfun4me, Nov 5, 2018 in forum: Mods and Upgrades
  15. 3dfun4me
    Post

    Community Favorite Marlin 1.1.9 Release for Robo R1+

    R1+ here, I had intermittent problems with the right z motor locking up. I think it was during the use of the pause command, I got the motor buzz...
    Post by: 3dfun4me, Sep 27, 2018 in forum: Mods and Upgrades
Showing results 1 to 15 of 15
Search Again