1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 4
  1. LordPeq
    Post

    Locked In Print

    It is still functioning but now, every time my computer goes to sleep, I cannot reconnect to Octoprint... Sometimes after a few minutes I am able...
    Post by: LordPeq, Jun 2, 2022 in forum: Troubleshooting
  2. LordPeq
    Post

    32-Bit Heart Transplant for the Robo R2

    Wow, I would love to see an understand your setup
    Post by: LordPeq, Jun 2, 2022 in forum: Projects
  3. LordPeq
    Post

    Locked In Print

    It was actually fine with a reboot, but since the card crapped out once, I am swapping the 8GB card for a 32GB and reflashing it
    Post by: LordPeq, May 31, 2022 in forum: Troubleshooting
  4. LordPeq
    Thread

    Locked In Print

    So I am thinking either my SD card is corrupted...again, or my Raspberry Pi took a dump. I cannot log into my printer via octoprint, the onscreen...
    Thread by: LordPeq, May 31, 2022, 32 replies, in forum: Troubleshooting
  5. LordPeq
    Post

    Unable to open Cura for Robo

    Ok for CURA 5 you need to create an account and download the OctoPrint plugin or you wont be able to connect. Second, create as custom FFF...
    Post by: LordPeq, May 31, 2022 in forum: Troubleshooting
  6. LordPeq
    Post

    32-Bit Heart Transplant for the Robo R2

    I had the same thought... a 32bit BTT Octopus, Raspberry pi and Klipper firmware... Did you ever go anywhere with this project?
    Post by: LordPeq, May 30, 2022 in forum: Projects
  7. LordPeq
    Post

    Wild Idea

    Thanks for the tips! I’ll marinate on the idea a bit
    Post by: LordPeq, May 30, 2022 in forum: Mods and Upgrades
  8. LordPeq
    Post

    Wild Idea

    I’d love to study your work… I am of the mind that if I can tweak this thing and swap out the electronics, I can have a really fast and well...
    Post by: LordPeq, May 30, 2022 in forum: Mods and Upgrades
  9. LordPeq
    Post

    Wild Idea

    And wouldn’t a better 32 but board take full advantage of the Robo? Like make it function to its physical max? My goal for the R2 is 100mm/s print...
    Post by: LordPeq, May 30, 2022 in forum: Mods and Upgrades
  10. LordPeq
    Post

    Wild Idea

    Interesting… I of course am on a quest for those ultra fast CoreXY boys crapping out a benchy in 14 minutes. Didn’t you rebuild your gantry?
    Post by: LordPeq, May 30, 2022 in forum: Mods and Upgrades
  11. LordPeq
    Post

    Wild Idea

    So if I am hearing you right, I could theoretically swap the boards, and go to Klipper but I would still be limited by the stock gantry? What...
    Post by: LordPeq, May 30, 2022 in forum: Mods and Upgrades
  12. LordPeq
    Post

    Cura 5

    Don't set up like a R1, do a custom FFF printer and plug in these settings.
    Post by: LordPeq, May 30, 2022 in forum: Software
  13. LordPeq
    Post

    Cura 5

    [ATTACH]
    Post by: LordPeq, May 30, 2022 in forum: Software
  14. LordPeq
    Post

    Cura 5

    [ATTACH]
    Post by: LordPeq, May 30, 2022 in forum: Software
  15. LordPeq
    Post

    Wild Idea

    Yeah I have a pi3 in there now. I have a spare 3 and a 4
    Post by: LordPeq, May 29, 2022 in forum: Mods and Upgrades
  16. LordPeq
    Thread

    Cura 5

    Hey everyone, I have been playing around with Cura 5 and my Robo3D R2. First impressions were rough as I had to install a few plugins to get it to...
    Thread by: LordPeq, May 29, 2022, 12 replies, in forum: Software
  17. LordPeq
    Thread

    Wild Idea

    So I have had my R2 since 2018, I took about a year off to educate myself a little more, get divorced and have the time to devote to my hobby....
    Thread by: LordPeq, May 29, 2022, 14 replies, in forum: Mods and Upgrades
  18. LordPeq
    Post

    IR Board/Partsbuilt buildtak material

    My board was testing as bad and then my SD card crashed... the new image and proper firmware restored my board and I now have auto-leveling...
    Post by: LordPeq, Apr 11, 2022 in forum: Troubleshooting
  19. LordPeq
    Post

    Printer had a stroke

    Makes total sense... I will be staying on my current firmware and I doubt there will be an updated OS... so I am going to just call it "good"...
    Post by: LordPeq, Apr 11, 2022 in forum: Troubleshooting
  20. LordPeq
    Post

    Printer had a stroke

    Makes total sense... I will be staying on my current firmware and I doubt there will be an updated OS... so I am going to just call it "good"...
    Post by: LordPeq, Apr 11, 2022 in forum: Troubleshooting
Showing results 41 to 60 of 64 Next >
Search Again
Page 3 of 4