1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Troubleshooting

Page 1 of 22
Sort by:
Title Start Date
Replies Views
Last Message ↓
  1. tkoco
    Locked Sticky

    R2 FAQ

    tkoco, Dec 24, 2019
    Replies:
    8
    Views:
    233
    tkoco
    tkoco
    Jan 13, 2020
  2. tkoco
    Sticky

    PID calibration

    tkoco, Sep 15, 2019
    Replies:
    1
    Views:
    639
    tkoco
    tkoco
    Dec 24, 2019
  3. tkoco
    Sticky

    Leveling the R2 Print Bed

    tkoco, Jul 30, 2019
    Replies:
    2
    Views:
    866
    tkoco
    tkoco
    Dec 24, 2019
  4. Omegagundam
    Sticky

    Printer error Bed not heating up

    Omegagundam, Nov 19, 2017 ... 2
    Replies:
    20
    Views:
    7,988
    Shrey
    Shrey
    Jan 3, 2018
  5. mark tomlinson
    Locked Sticky

    R2/C2 Documentation

    mark tomlinson, Jun 9, 2017
    Replies:
    2
    Views:
    3,715
    Geof
    Geof
    Nov 16, 2017
  6. Brandon Groves
    Locked Sticky

    Need an image of the R2's microsd card.

    Brandon Groves, Jun 17, 2017
    Replies:
    11
    Views:
    4,925
    Brandon Groves
    Brandon Groves
    Jun 17, 2017
  7. MGF

    Used Robo R2 missing parts

    MGF, Jan 3, 2020
    Replies:
    18
    Views:
    255
    MGF
    MGF
    Jan 19, 2020 at 1:30 PM
  8. BJS227

    help with first layer on section of bed

    BJS227, Jan 8, 2020
    Replies:
    2
    Views:
    92
    tkoco
    tkoco
    Jan 10, 2020
  9. Clay Raber

    Z Axis moves upward during Fine Tune Wizard

    Clay Raber, Jan 8, 2020
    Replies:
    4
    Views:
    83
    Clay Raber
    Clay Raber
    Jan 9, 2020
  10. Paul1967

    Heater is not found error

    Paul1967, Dec 26, 2019
    Replies:
    10
    Views:
    190
    WheresWaldo
    WheresWaldo
    Jan 1, 2020
  11. Joseph Everhart

    Ribbon cable pinouts

    Joseph Everhart, Dec 29, 2019
    Replies:
    2
    Views:
    98
    Joseph Everhart
    Joseph Everhart
    Dec 29, 2019
  12. adikted2astro

    Vase Mode Leaving Voids in Sliced Models

    adikted2astro, Dec 10, 2019
    Replies:
    12
    Views:
    189
    mark tomlinson
    mark tomlinson
    Dec 28, 2019
  13. studiver13
    Locked

    Connection Interrupted

    studiver13, Dec 22, 2019 ... 2 3
    Replies:
    43
    Views:
    410
    mark tomlinson
    mark tomlinson
    Dec 26, 2019
  14. adikted2astro

    Replacing bushing covers on x/y axis rods

    adikted2astro, Nov 19, 2019 ... 2
    Replies:
    27
    Views:
    479
    tkoco
    tkoco
    Dec 21, 2019
  15. Eric Viglotti

    Dried Spaghetti on bottom layer but then fine for all other layers

    Eric Viglotti, Dec 8, 2019 ... 2
    Replies:
    20
    Views:
    288
    adikted2astro
    adikted2astro
    Dec 21, 2019
  16. dairdevil
    Locked

    Z Axis Wizard Problems

    dairdevil, Dec 16, 2019
    Replies:
    17
    Views:
    227
    mark tomlinson
    mark tomlinson
    Dec 21, 2019
  17. RoboticsRob

    Fix for R2 Connection Interrupted Error

    RoboticsRob, Dec 17, 2019
    Replies:
    2
    Views:
    121
    RoboticsRob
    RoboticsRob
    Dec 17, 2019
  18. Trevor C

    where can I get a replacement power plug

    Trevor C, May 23, 2018 ... 2
    Replies:
    27
    Views:
    1,741
    RoboticsRob
    RoboticsRob
    Dec 17, 2019
  19. Shrey

    First layer ripple

    Shrey, Feb 4, 2018
    Replies:
    18
    Views:
    1,261
    Lance Weston
    Lance Weston
    Dec 12, 2019
  20. Kizmet

    Robo R2 Z Wizard wont calibrate correctly

    Kizmet, Nov 22, 2019 ... 2
    Replies:
    25
    Views:
    412
    tkoco
    tkoco
    Dec 10, 2019
  21. Paul1967

    Issue with R2 Cura

    Paul1967, Dec 6, 2019
    Replies:
    8
    Views:
    210
    tkoco
    tkoco
    Dec 9, 2019
  22. MikeDanatos

    New R2 producing 'string art'

    MikeDanatos, Nov 27, 2019
    Replies:
    10
    Views:
    226
    tkoco
    tkoco
    Dec 4, 2019
  23. Lance Weston

    Filament sensor problems

    Lance Weston, Nov 23, 2019
    Replies:
    7
    Views:
    128
    mark tomlinson
    mark tomlinson
    Nov 23, 2019
  24. RoboticsRob

    R2 reports constant, incorrect extruder temperature

    RoboticsRob, Aug 20, 2019 ... 2
    Replies:
    30
    Views:
    804
    mark tomlinson
    mark tomlinson
    Nov 14, 2019
  25. Dragon

    Robo R2 Camera Issue

    Dragon, Nov 1, 2019
    Replies:
    4
    Views:
    176
    Dragon
    Dragon
    Nov 2, 2019
  26. Michael hineman

    Camera Not working

    Michael hineman, Dec 31, 2017 ... 2
    Replies:
    29
    Views:
    2,010
    tkoco
    tkoco
    Nov 1, 2019
Showing threads 1 to 20 of 425

Thread Display Options

Loading...
Page 1 of 22