1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 5
  1. Terry Reilley
    Post

    Solved Y axis jumps, sticks, screws up 90% of prints.

    Rather than start a new thread for what appears to be the same symptoms, I'll tag on here. After replacing my hot end with a new Hexagon and...
    Post by: Terry Reilley, Mar 28, 2016 in forum: Troubleshooting
  2. Terry Reilley
    Post

    E3D v6 Information, Installation Guides, and Review

    Does anyone have an opinion about this Wade modification as opposed to a novice drilling the stock part in order to accommodate the E3D v6?...
    Post by: Terry Reilley, Mar 22, 2016 in forum: Mods and Upgrades
  3. Terry Reilley
    Post

    Solved ABS on with the factory hex hotend?

    I print about 60% of the time in ABS at 235 and heatbed at 80. I also use PEI and just completed my Kelly enclosure this morning, but can't...
    Post by: Terry Reilley, Mar 22, 2016 in forum: General Questions
  4. Terry Reilley
    Post

    Solved Removing Hotend on R1+

    I thought upgrading to the E3Dv6 wasn't exactly "drop and play". I've read Mike's guide and it seems like some drilling is required to accommodate...
    Post by: Terry Reilley, Mar 18, 2016 in forum: Troubleshooting
  5. Terry Reilley
    Post

    PEI Print Bed

    At first,the parts popped off with no effort whatsoever after cooling off and that was less than 3 weeks ago. My initial thought was that I had...
    Post by: Terry Reilley, Mar 17, 2016 in forum: Mods and Upgrades
  6. Terry Reilley
    Post

    PEI Print Bed

    OK, so here's another issue for the day I'd like to share: I bought and installed a sheet of PEI on my chipped bed about 3 weeks ago. I'm a...
    Post by: Terry Reilley, Mar 17, 2016 in forum: Mods and Upgrades
  7. Terry Reilley
    Post

    Simplify 3d

    Well I spoke too soon. An 18 hour print failed about 85% into it due to warping of the ABS. Tried a shorter print and it did the same. I don't...
    Post by: Terry Reilley, Mar 15, 2016 in forum: Software
  8. Terry Reilley
    Post

    Simplify 3d

    OK, my problem is solved. Z Offset was the issue. I had to set it to -0.35 and once I did that, my perimeters were closed and the print is...
    Post by: Terry Reilley, Mar 15, 2016 in forum: Software
  9. Terry Reilley
    Post

    Simplify 3d

    Since I sent the first profile, I've been adjusting the z-offset lower by 0.05 increments. I must be making some progress because the filament...
    Post by: Terry Reilley, Mar 14, 2016 in forum: Software
  10. Terry Reilley
    Post

    Simplify 3d

    That's odd because I have ABS set to print at 235 and 80. Not sure why that profile shows otherwise except maybe I sent the wrong one. Check...
    Post by: Terry Reilley, Mar 14, 2016 in forum: Software
  11. Terry Reilley
    Post

    Simplify 3d

    OK, here we go!
    Post by: Terry Reilley, Mar 14, 2016 in forum: Software
  12. Terry Reilley
    Post

    Simplify 3d

    Well, leave it to me to be the doom and gloom guy for what I initially thought was the best $149.00 I've spent thus far. I purchased S3D about a...
    Post by: Terry Reilley, Mar 14, 2016 in forum: Software
  13. Terry Reilley
    Post

    Unresolved "Branchy" Supports

    OK thanks - I will contact them and see what they have to say.
    Post by: Terry Reilley, Mar 7, 2016 in forum: Troubleshooting
  14. Terry Reilley
    Thread

    Unresolved "Branchy" Supports

    Hi gang! Printing with Hatchbox ABS at 230 and getting really ugly supports in MatterControl here. Here's a photo of the supports. They should...
    Thread by: Terry Reilley, Mar 7, 2016, 2 replies, in forum: Troubleshooting
  15. Terry Reilley
    Post

    NinjaFlex filament

    Well, shucks. I ordered this exact part yesterday and what they shipped had a wall thickness of .04" verses the advertised .085", so my test PLA...
    Post by: Terry Reilley, Mar 3, 2016 in forum: Printing Filament
  16. Terry Reilley
    Post

    PEI Print Bed

    Can you use some sort of clips to secure the PEI rather than using the adhesive tape? I might have missed that in this discussion, so I apologize...
    Post by: Terry Reilley, Feb 25, 2016 in forum: Mods and Upgrades
  17. Terry Reilley
    Post

    Solved Bad day - clogged Hexagon hot end

    OK, it took quite a while, but I was finally able to get the filament out! The heat block loosened up, so I took advantage and removed it....
    Post by: Terry Reilley, Feb 24, 2016 in forum: Troubleshooting
  18. Terry Reilley
    Post

    Solved Bad day - clogged Hexagon hot end

    OK, I will give that a try - thanks!
    Post by: Terry Reilley, Feb 24, 2016 in forum: Troubleshooting
  19. Terry Reilley
    Thread

    Solved Bad day - clogged Hexagon hot end

    Today is just not my day. After finding a bent Z screw and chips on my heated bed, I have now managed to clog my hot end up with ABS. I was...
    Thread by: Terry Reilley, Feb 24, 2016, 6 replies, in forum: Troubleshooting
  20. Terry Reilley
    Post

    Solved Anyone ever seen this?

    I literally just found two chips in mine as well less than 1/2 hour ago while cleaning the bed for another print. It looks more like the nozzle...
    Post by: Terry Reilley, Feb 19, 2016 in forum: Troubleshooting
Showing results 61 to 80 of 87 Next >
Search Again
Page 4 of 5