1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 4
  1. Jay312
    Post

    Solved Print Bed "Upgrade"

    Ive been trying to find one for sale online, they are sold out on GeckoTek
    Post by: Jay312, Aug 2, 2017 in forum: General Questions
  2. Jay312
    Post

    Solved Problem

    Problem solved it just was not sitting proper on the left side, couple of wiggles in the right direction ended up helping
    Post by: Jay312, Jul 29, 2017 in forum: Troubleshooting
  3. Jay312
    Post

    Solved Problem

    Mark So this side is the problem when I press it down during a g29 it works. How do I get this down so it's activating the sensor? [MEDIA] Can...
    Post by: Jay312, Jul 28, 2017 in forum: Troubleshooting
  4. Jay312
    Thread

    Solved Problem

    After installing the E3D V6 it's printing in the air and leveling in the air. I did check the wires because that's almost always the issue, but...
    Thread by: Jay312, Jul 28, 2017, 3 replies, in forum: Troubleshooting
  5. Jay312
    Post

    E3D V6 Help

    Is it ok if I connect the E3D V6 hot end fan to the same place as that small robo fan was? If I wire the same connector on it of course. Or is it...
    Post by: Jay312, Jul 26, 2017 in forum: Mods and Upgrades
  6. Jay312
    Post

    E3D V6 Help

    Thanks guys
    Post by: Jay312, Jul 26, 2017 in forum: Mods and Upgrades
  7. Jay312
    Post

    E3D V6 Help

    if it did fully I would t have any questions, it shows what to change the firmware to and what lines to change, but I could not find how to pull...
    Post by: Jay312, Jul 26, 2017 in forum: Mods and Upgrades
  8. Jay312
    Post

    E3D V6 Help

    Almost done with this project, now the big questions. How do I update the firmware to the newest version exactly for the R1 plus? And how do I...
    Post by: Jay312, Jul 26, 2017 in forum: Mods and Upgrades
  9. Jay312
    Post

    E3D V6 Help

    unreal I did not print the fan holder in step 2, so frustrated
    Post by: Jay312, Jul 18, 2017 in forum: Mods and Upgrades
  10. Jay312
    Post

    E3D V6 Help

    Got the hole drilled already, not nearly as bad as I thought. 2nd question is this good for the nozzle or should the nozzle be right up against...
    Post by: Jay312, Jul 17, 2017 in forum: Mods and Upgrades
  11. Jay312
    Thread

    E3D V6 Help

    Before I drill a hole for the tube do I need to take this apart completely, I'm worried about hitting that metal thing that feeds the filament...
    Thread by: Jay312, Jul 17, 2017, 14 replies, in forum: Mods and Upgrades
  12. Jay312
    Post

    Filament spool print

    Thanks it came out real nice, the more I use the Carbon fiber PLA from Robo the more I like it. It makes for some smooth prints and quality parts
    Post by: Jay312, Apr 7, 2017 in forum: Show and Tell
  13. Jay312
    Post

    Solved Sites like thingiverse?

    What are some of your favorites Mark?
    Post by: Jay312, Apr 3, 2017 in forum: General Questions
  14. Jay312
    Post

    Filament spool print

    Here it is assembled on the printer
    Post by: Jay312, Apr 3, 2017 in forum: Show and Tell
  15. Jay312
    Thread

    Filament spool print

    Printed on my R1 Plus with Robo Carbon Fiber PLA I actually used two different ithingverse builds to make this one build. Snaps in sturdy.
    Thread by: Jay312, Apr 3, 2017, 5 replies, in forum: Show and Tell
  16. Jay312
    Thread

    Solved Sites like thingiverse?

    Looking for some other sites like thingiverse I know I have to be missing out on some cool ones. What does everyone like?
    Thread by: Jay312, Apr 3, 2017, 8 replies, in forum: General Questions
  17. Jay312
    Post

    Solved Auto leveling problem

    Thank you so much everything is all good.
    Post by: Jay312, Apr 2, 2017 in forum: Troubleshooting
  18. Jay312
    Post

    Solved Auto leveling problem

    Fixed it perfectly thank you
    Post by: Jay312, Apr 2, 2017 in forum: Troubleshooting
  19. Jay312
    Post

    Solved Auto leveling problem

    The very end or the middle one?
    Post by: Jay312, Apr 2, 2017 in forum: Troubleshooting
  20. Jay312
    Post

    Solved Auto leveling problem

    Could it be this? It looks up [ATTACH]
    Post by: Jay312, Apr 2, 2017 in forum: Troubleshooting
Showing results 21 to 40 of 64 Next >
Search Again
Page 2 of 4