1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    so the end stop is on the left raid bracket right. There are 3 lead terminals on the momentary switch. From looking at it from the top down, how...
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  2. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    ok
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  3. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    I typed in m119 but it just says their all triggered.[ATTACH]
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  4. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    I swapped the wires and it still does the same thing. :(
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  5. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    So I just swap the red and black wires on the X axis home switch? Ill try it.
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  6. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Thats why im so confused, because I can hit the X+ button and it will move the specified distance to the right. Is that normal?
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  7. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Be advised I can move each axis individually by using the X-, X+, Y-, Y+, and Z-, Z+ buttons so they responding appropriately to the software and...
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  8. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Ok, here goes another attempt! I tried what you said and it homes EXCEPT! the X axis is stair stepping to the right each time I press Home. It...
    Post by: jOeBrokeIt, Aug 25, 2016 in forum: Troubleshooting
  9. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Thanks a lot Danzca6. I think I had enough battling for the night as well. I am in San Francisco by the way. I will try out your tips tomorrow and...
    Post by: jOeBrokeIt, Aug 24, 2016 in forum: Troubleshooting
  10. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    No success unfortunately... It is going all over the place and going higher and higher up. Its even ramming the bed and extruder to the very end :(
    Post by: jOeBrokeIt, Aug 24, 2016 in forum: Troubleshooting
  11. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Ah nice! I think I got it! It homes all axis now. The problem was the gap between the hex nut and the end stop. Thanks a bunch man! :) Now I...
    Post by: jOeBrokeIt, Aug 24, 2016 in forum: Troubleshooting
  12. jOeBrokeIt
    Post

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Im not sure of exactly what you are talking about. I have no idea how things were originally supposed to be connected and configured. I swapped...
    Post by: jOeBrokeIt, Aug 24, 2016 in forum: Troubleshooting
  13. jOeBrokeIt
    Thread

    Solved Help! Wires to stepper motor got tangled and unplugged.

    Having a problem with my ROBO 3D R1 Plus It was working fine since I got it about a week ago and made some pretty good prints right out of the...
    Thread by: jOeBrokeIt, Aug 24, 2016, 38 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 33 of 33
Search Again
Page 2 of 2