1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Michael hineman
    Post

    OK. I would like a little insight about the firmware, roboOS, Octoprint.

    I found another issue. I can get printer to boot by loading backup image to the sd card, but if I turn the printer off it will not boot up any...
    Post by: Michael hineman, Dec 27, 2017 in forum: Software
  2. Michael hineman
    Post

    OK. I would like a little insight about the firmware, roboOS, Octoprint.

    I do not even have this screen. [ATTACH]
    Post by: Michael hineman, Dec 27, 2017 in forum: Software
  3. Michael hineman
    Post

    OK. I would like a little insight about the firmware, roboOS, Octoprint.

    This print screen has more information then my print screen. This screen shows set points for temp as well as a completion bar and time left to...
    Post by: Michael hineman, Dec 27, 2017 in forum: Software
  4. Michael hineman
    Post

    OK. I would like a little insight about the firmware, roboOS, Octoprint.

    I do NOT have the ability to sort like shown in this picture[ATTACH]
    Post by: Michael hineman, Dec 27, 2017 in forum: Software
  5. Michael hineman
    Post

    OK. I would like a little insight about the firmware, roboOS, Octoprint.

    Here is my wizard screen. and file screen. I do not have any ability to sort the files like I have seen. I can not see update removing...
    Post by: Michael hineman, Dec 27, 2017 in forum: Software
  6. Michael hineman
    Post

    Lost main board connection?

    Printing PLA, temp 200, bed 50, happened while printing 2 twice, It has not happened again. I believe it had to do with the usb drive.
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  7. Michael hineman
    Thread

    OK. I would like a little insight about the firmware, roboOS, Octoprint.

    I am wanting to know more about each of these, particularly as to what each do? My roboOS is running the version 1.8.1-r2.1. I updated it that out...
    Thread by: Michael hineman, Dec 27, 2017, 9 replies, in forum: Software
  8. Michael hineman
    Post

    Lost main board connection?

    Just printing and it dies. So far so good. I am in about a 3 hour print and it is doing good.
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  9. Michael hineman
    Post

    Lost main board connection?

    Yes I backed it up but still can not get the firmware to update. Sent from my SAMSUNG-SM-N910A using Tapatalk
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  10. Michael hineman
    Post

    What is causing this ?

    Is your z axis ballscrew bent? Mine was and it only would effect the print every full rotate of the screw. Sent from my SAMSUNG-SM-N910A using...
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  11. Michael hineman
    Post

    Lost main board connection?

    Yes and reloaded it. See if happens anymore. Sent from my SAMSUNG-SM-N910A using Tapatalk
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  12. Michael hineman
    Post

    What is causing this ?

    I am by far a pro. But looks like the issue is due to retraction. Sent from my SAMSUNG-SM-N910A using Tapatalk
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  13. Michael hineman
    Post

    Lost main board connection?

    This is not the lost bed connection. This is something different that I believe is related to the usb drive. My robo usb died only after about 7...
    Post by: Michael hineman, Dec 27, 2017 in forum: Troubleshooting
  14. Michael hineman
    Thread

    Lost main board connection?

    What is this? I can start a print and then get this. Everything works fine I see not reason for this error. I start again and then everything is...
    Thread by: Michael hineman, Dec 27, 2017, 33 replies, in forum: Troubleshooting
  15. Michael hineman
    Post

    Do I need to update the firmware of my robo 3d r2?

    OK Great thanks for the info.
    Post by: Michael hineman, Dec 22, 2017 in forum: General Questions
  16. Michael hineman
    Post

    Do I need to update the firmware of my robo 3d r2?

    OK. Stupid question where is the SD card at? and how to back it up? I have already updated the RoboOS.
    Post by: Michael hineman, Dec 22, 2017 in forum: General Questions
  17. Michael hineman
    Thread

    Do I need to update the firmware of my robo 3d r2?

    I do not have the fine tune Z option under the wizard section. I also have noticed that my menus look different than those of you tube. I can only...
    Thread by: Michael hineman, Dec 22, 2017, 8 replies, in forum: General Questions
Find older messages
Showing results 21 to 37 of 37
Search Again
Page 2 of 2