1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Folk Hero
    Post

    Solved Broken Piece

    Thanks to everyone. Of all the hobbies I have been involved in in my life 3D Printer enthusiasts are the most responsive and helpful of any of...
    Post by: Folk Hero, Jun 1, 2017 in forum: Troubleshooting
  2. Folk Hero
    Post

    Solved Broken Piece

    I'm going to try that but was wondering where I can get a picture/diagram of the belt routing? Tim
    Post by: Folk Hero, Jun 1, 2017 in forum: Troubleshooting
  3. Folk Hero
    Thread

    Solved Broken Piece

    This broke on the belt drive for the table of my ROBO 3D. Is this something I can get from ROBO? [IMG] Tim
    Thread by: Folk Hero, May 31, 2017, 9 replies, in forum: Troubleshooting
  4. Folk Hero
    Post

    Considering buying a ROBO 3D R1+

    I like mine so far. I've only had a couple of ID10T errors. Of course I only bought mine to back up my Tarantula. It's my workhorse. Tim
    Post by: Folk Hero, May 26, 2017 in forum: General Questions
  5. Folk Hero
    Post

    Solved Print head height

    That was the problem (figured it out about 3:15 this morning). When I had laid it on it's face to fix the power issue the switch moved just enough...
    Post by: Folk Hero, May 26, 2017 in forum: General Questions
  6. Folk Hero
    Post

    Solved Print head height

    The videos nice but not really helping. I ran it again and noticed that each time it goes to one of the points on the bed for calibration it...
    Post by: Folk Hero, May 25, 2017 in forum: General Questions
  7. Folk Hero
    Thread

    Solved Print head height

    I didn't put this in troubleshooting because I'm pretty sure it's just stupidity on my part. I fire up the printer, load the PLA after the temps...
    Thread by: Folk Hero, May 25, 2017, 5 replies, in forum: General Questions
  8. Folk Hero
    Post

    Solved Power Off

    Turns out it was a brand new defective power cord where it plugs in the wall. Thanks Tim
    Post by: Folk Hero, May 22, 2017 in forum: Troubleshooting
  9. Folk Hero
    Post

    Solved Power Off

    Nope. I've tried unplugging it and plugging it back in and flipped the on/off switch half a dozen times and it won't even light up the led light...
    Post by: Folk Hero, May 22, 2017 in forum: Troubleshooting
  10. Folk Hero
    Post

    Solved Power Off

    Not that I can tell. According to what I'm seeing the computer thinks everything is OK. I read somewhere that the RAMPS boards can sometimes have...
    Post by: Folk Hero, May 22, 2017 in forum: Troubleshooting
  11. Folk Hero
    Post

    Solved Power Off

    This is what I'm getting, but being unfamiliar with it I'm not seeing anything awry. Tim
    Post by: Folk Hero, May 22, 2017 in forum: Troubleshooting
  12. Folk Hero
    Post

    Solved Power Off

    I'm using MatterControl 1.5 which shows it's connected. It's reading the bed and extruder temps which are with no power going to them low. Tim
    Post by: Folk Hero, May 22, 2017 in forum: Troubleshooting
  13. Folk Hero
    Post

    Solved Power Off

    I'm running it from the computer. Where would I look for error codes? Tim
    Post by: Folk Hero, May 22, 2017 in forum: Troubleshooting
  14. Folk Hero
    Thread

    Solved Power Off

    I bought a used R1 from a guy we set up and printed great. I brought it home installed the software and thought I'd print the calibration circle....
    Thread by: Folk Hero, May 21, 2017, 14 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 34 of 34
Search Again
Page 2 of 2