1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Johndrindak
    Post

    Unanswered why cant I add a raft on matter control

    I'm already using the advanced settings
    Post by: Johndrindak, Mar 16, 2016 in forum: Troubleshooting
  2. Johndrindak
    Post

    Unanswered why cant I add a raft on matter control

    [ATTACH] [ATTACH]
    Post by: Johndrindak, Mar 16, 2016 in forum: Troubleshooting
  3. Johndrindak
    Post

    Unanswered why cant I add a raft on matter control

    there are no settings for rafts there
    Post by: Johndrindak, Mar 16, 2016 in forum: Troubleshooting
  4. Johndrindak
    Thread

    Unanswered why cant I add a raft on matter control

    I am on the advanced settings an I hit the skirt and raft section and it only lets me change skirt settings
    Thread by: Johndrindak, Mar 16, 2016, 14 replies, in forum: Troubleshooting
  5. Johndrindak
    Thread

    Any reason I should keep a old power supply

    I'm replacing my power supply because my old one isn't good. Are there any parts in there or reasons to keep the old one. P.s. Sorry if this is...
    Thread by: Johndrindak, Feb 25, 2016, 2 replies, in forum: General Questions
  6. Johndrindak
    Thread

    Unresolved My printer won't turn on

    i was just about to print something when it suddenly shut off and initially when I turned it on the LED's would flicker. Now the machine doesn't...
    Thread by: Johndrindak, Feb 23, 2016, 6 replies, in forum: Troubleshooting
  7. Johndrindak
    Post

    Unresolved how to I get at the thermister

    which one is the heater cartridge screw also thank you so much!
    Post by: Johndrindak, Feb 22, 2016 in forum: Troubleshooting
  8. Johndrindak
    Post

    Unresolved how to I get at the thermister

    yes I am using the default hot end
    Post by: Johndrindak, Feb 22, 2016 in forum: Troubleshooting
  9. Johndrindak
    Thread

    Unresolved how to I get at the thermister

    Please step by step from the very beginning. Pretend I'm a 6 year old or something. Also how do i know if it isn't correct
    Thread by: Johndrindak, Feb 22, 2016, 5 replies, in forum: Troubleshooting
  10. Johndrindak
    Thread

    Unresolved Not printing after bed leveling

    after the leveling it stays on the last spot
    Thread by: Johndrindak, Feb 21, 2016, 3 replies, in forum: Troubleshooting
  11. Johndrindak
    Thread

    Unanswered printer stopping in the middle of prints

    the terminal says <-Error:Line Number is not Last Line Number+1, Last Line:9605 [600.384] <-Resend: 6906 [600.384] <-ok [600.600.384] what does...
    Thread by: Johndrindak, Feb 20, 2016, 1 replies, in forum: Troubleshooting
  12. Johndrindak
    Thread

    Solved M999 error

    I have seen people post this but the printer still heats up and it displays that on the software as well
    Thread by: Johndrindak, Feb 20, 2016, 2 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again