1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. znet3d
    Thread

    Unanswered Multi color prints getting back to exact paused location

    So I have been trying out printing with multi color. I am using MC, I pause the printer at a desired layer, move the extruder up about 30mm,...
    Thread by: znet3d, Jun 16, 2016, 3 replies, in forum: General Questions
  2. znet3d
    Post

    Multiple colors with single extruder

    I tried to do this using the MC slicer. worked great the first time I tried it, by simply pausing it moving 30mm up, change filament, move 30mm...
    Post by: znet3d, Jun 15, 2016 in forum: Printing Filament
  3. znet3d
    Post

    Answered Printer went crazy

    What I think happened was that the tie strap at the top that was holding the wires was to tight and got caught when moving. I have replaced it...
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  4. znet3d
    Post

    Answered Chunks of glass came off with print

    I just wanted to be sure, if I cover the bed with LEXAN, do I then still put the blue tape on the LEXAN or use the glue stick like on the glass bed?
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  5. znet3d
    Post

    Answered Chunks of glass came off with print

    Thanks for all the advice, ROBO support was great, they are shipping me a replacement bed for a discounted price, I ordered the LEXAN sheet but I...
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  6. znet3d
    Post

    Answered Chunks of glass came off with print

    So something like this will work? Lexan Sheet - Polycarbonate - .030" - 1/32" Thick, Clear, 12" x 12"...
    Post by: znet3d, Jun 15, 2016 in forum: Troubleshooting
  7. znet3d
    Thread

    Answered Chunks of glass came off with print

    So this morning I go to pull off a printed part of the glass bed, and noticed that chunks of glass just came off stuck to my printed part and now...
    Thread by: znet3d, Jun 14, 2016, 16 replies, in forum: Troubleshooting
  8. znet3d
    Post

    Answered Printer went crazy

    Anything I can do, should be doing to help prevent the switches from getting stuck? Or are there things I can make for the screws so that it stops...
    Post by: znet3d, Apr 19, 2016 in forum: Troubleshooting
  9. znet3d
    Thread

    Answered Printer went crazy

    So, I started printing the Robo3D tool holder from Thingverse: http://www.thingiverse.com/thing:913811 I watched it do the first layer and...
    Thread by: znet3d, Apr 18, 2016, 4 replies, in forum: Troubleshooting
  10. znet3d
    Post

    Solved Bottom layer has gaps

    Hello, I apologies it took me couple of days to tryout some of the suggestions you guys provided. So I used the Macro buttons to play with...
    Post by: znet3d, Apr 7, 2016 in forum: Troubleshooting
  11. znet3d
    Post

    Solved Bottom layer has gaps

    Thank you for all your feedback, I am using the hatchbox filament and will try to lower the temp. The printer bed was nice and clean when I did...
    Post by: znet3d, Apr 4, 2016 in forum: Troubleshooting
  12. znet3d
    Thread

    Solved Bottom layer has gaps

    Dear Robo3d community, This is my first 3D printer and I have been learning a lot and I have a lot more to learn, I was hoping someone could help...
    Thread by: znet3d, Apr 4, 2016, 9 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again