1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. kjfaris
    Post

    Solved Printer Goes Wild

    Well I don't know what to say. I came home last night and tore the printer down. All limit switches were properly secured and wires connected....
    Post by: kjfaris, Jul 7, 2016 in forum: Troubleshooting
  2. kjfaris
    Post

    Solved Printer Goes Wild

    I can see the logic with the switch breaking contact prematurely and causing the bed leveling issue, but what would account for the head slamming...
    Post by: kjfaris, Jul 5, 2016 in forum: Troubleshooting
  3. kjfaris
    Post

    Solved Printer Goes Wild

    Checked bed is pretty level just moving the x across the bed at different y positions and the switches are in the proper position. Early morning...
    Post by: kjfaris, Jul 5, 2016 in forum: Troubleshooting
  4. kjfaris
    Post

    Solved Printer Goes Wild

    Definitely not disconnected or loose, but I will check with a meter for proper operation, thanks
    Post by: kjfaris, Jul 5, 2016 in forum: Troubleshooting
  5. kjfaris
    Thread

    Solved Printer Goes Wild

    Well I have been reading about all these problems here and being thankful that it hasn't happened to me and out of the blue epic fail. I used the...
    Thread by: kjfaris, Jul 5, 2016, 11 replies, in forum: Troubleshooting
  6. kjfaris
    Post

    Solved Belt Tension

    Thank you
    Post by: kjfaris, Jul 4, 2016 in forum: Troubleshooting
  7. kjfaris
    Post

    Solved Belt Tension

    I'm looking at your picture and it appears that your is not continuous, is that true. Mine is one piece continuous and had one wire tie right at...
    Post by: kjfaris, Jul 1, 2016 in forum: Troubleshooting
  8. kjfaris
    Thread

    Solved Belt Tension

    Hello everyone, Having a case of the dumbies, took down my R1 plus to prepare for the installation of an E3D V6 head and payed attention to...
    Thread by: kjfaris, Jul 1, 2016, 8 replies, in forum: Troubleshooting
  9. kjfaris
    Post

    Solved Leaking Heat Block on Inlet

    Appreciate the offer, I'll make it work somehow, good experience. It's printing now for about 2 hours with no problem other than an occasional...
    Post by: kjfaris, Jun 25, 2016 in forum: Troubleshooting
  10. kjfaris
    Post

    Solved Leaking Heat Block on Inlet

    Thanks, that what I thought I called support and they were not helpful, even offered to by a new head, they don't have them and couldn't tell...
    Post by: kjfaris, Jun 25, 2016 in forum: Troubleshooting
  11. kjfaris
    Thread

    Solved Leaking Heat Block on Inlet

    HI, I have had my printer an R1 plus for about a month and have been learning, experimenting and lurking on the forums and picking up a lot of...
    Thread by: kjfaris, Jun 25, 2016, 5 replies, in forum: Troubleshooting
  12. kjfaris
    Post

    Hello, new member

    Well the sun isn't shining much by me today, but I am enjoying my Robo. I am rapidly reaching the point where I'll be completely dangerous to my...
    Post by: kjfaris, May 30, 2016 in forum: United States of America
  13. kjfaris
    Post

    Hello, new member

    Thank you looking forward picking a lot of brains Sent from my iPad using Tapatalk
    Post by: kjfaris, May 23, 2016 in forum: United States of America
  14. kjfaris
    Post

    Hello, new member

    R1+ Sent from my iPad using Tapatalk
    Post by: kjfaris, May 23, 2016 in forum: United States of America
  15. kjfaris
    Thread

    Hello, new member

    Hello, Completely new to 3D printing something I have been wanting to do. So with the price and revues I read I just purchased a ROBO and am...
    Thread by: kjfaris, May 22, 2016, 9 replies, in forum: United States of America
Showing results 1 to 15 of 15
Search Again