1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. DH7
    Post

    Solved MakeShaper PLA Settings

    Weird question - in a PID tuning post you mention that the firmware should be edited after PID tuning, and someone said there's technically a...
    Post by: DH7, Aug 26, 2016 in forum: General Questions
  2. DH7
    Post

    Solved MakeShaper PLA Settings

    Thanks, I actually got a replacement hexagonal one from Amazon (robo is sold out, also the shipping speed from Amazon seems much better). It seems...
    Post by: DH7, Aug 26, 2016 in forum: General Questions
  3. DH7
    Post

    Solved MakeShaper PLA Settings

    I don't think my experience is the norm, I'm pretty sure I just managed to mess up the heatbreak in the process. One thing to consider according...
    Post by: DH7, Aug 26, 2016 in forum: General Questions
  4. DH7
    Post

    Solved MakeShaper PLA Settings

    I was looking into the e3dv6, but I'm trying not to edit the firmware. Does the Prometheus v2 require a firmware adjustment as well? EDIT: Just...
    Post by: DH7, Aug 19, 2016 in forum: General Questions
  5. DH7
    Post

    Solved MakeShaper PLA Settings

    Alright, thanks! I seem to have something catching inside my hot break, literally tore it down 4 times now, tried ABS instead of PLA, everything's...
    Post by: DH7, Aug 19, 2016 in forum: General Questions
  6. DH7
    Post

    Solved MakeShaper PLA Settings

    Trying to get the extruder up an running again, just with hatchbox PLA. Does the standard R1+ hotend have a PTFE liner?
    Post by: DH7, Aug 18, 2016 in forum: General Questions
  7. DH7
    Post

    Solved MakeShaper PLA Settings

    EDIT: Had a heat break jam, cleared it out, rebuilding the hot end now for a lower temp test. I was sent a simplify3D profile from another Robo...
    Post by: DH7, Aug 18, 2016 in forum: General Questions
  8. DH7
    Post

    Solved MakeShaper PLA Settings

    After the failed print a lump of PLA oozed out, suggesting there was a backup inside. Also it was clogged when i switched to my good PLA. Attached...
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  9. DH7
    Post

    Solved MakeShaper PLA Settings

    I'll try to get a pic of the hobb bolt. Here's a link to the video - the only thing thats helpful is you can hear the skip sound. [MEDIA] My...
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  10. DH7
    Post

    Solved MakeShaper PLA Settings

    My test print failed so I was able to get pictures. Attached is a picture of the bite marks, the failed print, is there a way to upload video?
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  11. DH7
    Post

    Solved MakeShaper PLA Settings

    Im running a quick print right now. It usually starts skipping within 10 minutes. I can upload a pic of the print failure and hopefully some video...
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  12. DH7
    Post

    Solved MakeShaper PLA Settings

    Calipers are reading 1.78mm going in. I am seeing large teeth marks when it skips.
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  13. DH7
    Post

    Solved MakeShaper PLA Settings

    My ProMolt PLA is feeding fine, no skips.
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  14. DH7
    Post

    Solved MakeShaper PLA Settings

    So im switching-off experimenting with 2 different PLAs from them - white and black. I had under-extrusion/skipping issues from both, slowing...
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  15. DH7
    Post

    Solved MakeShaper PLA Settings

    I assumed the same, that's why I'm going to try an oiler, but I spoke to the manufacturer and they mentioned that compared to other filaments...
    Post by: DH7, Aug 17, 2016 in forum: General Questions
  16. DH7
    Thread

    Solved MakeShaper PLA Settings

    I just bought some MakeShaper PLA. I'm trying to get the settings right in Simplify3D. If anyone has any experience with it, input would be...
    Thread by: DH7, Aug 17, 2016, 48 replies, in forum: General Questions
Showing results 1 to 16 of 16
Search Again