1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    Ok I think i've resolved my issue with the heated bed heating up during a print. I was putting google through it's paces and looking in every...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  2. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    Ok i tried running the same part in MatterControl and after the first 2 layers printed the temp started climbing again. I cancelled the print job...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  3. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    Ok did a bit of digging and now I think I've gotten rid of the binding. I lowered the z axis as low as I could using 1mm jogs. I then tilted the...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  4. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    I removed the x axis from the z axis and was able to jog up and down 1,10,100mm with no issues. As soon as I put the x axis back on the binding...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  5. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    I reinstalled the 5/16" firmware because that was letting me jog up and down no matter how far. I then changed the line you gave me. The jogging...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  6. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    Ok I've gone back to the 5/16" firmware and made the change to the z axis steps but now I'm running into the problem that when I jog 10mm or 100mm...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  7. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    OK so here's where I'm at now. I've reinstalled the 8mm firmware and the probblem I was having doing large movements is still persisting. While...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  8. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    Ok I just jog Z up 100mm and after I measured it the actual movement distance was 88mm, guess that means I have 8mm rods after all? So I'm guess...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  9. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    This all happened because I just installed both a new arduino and ramps board. What bothers me is that as long as I'm not printing and have the...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  10. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    Like I said in my original post I tried the R1 8mm firmware and had issues moving the z axis over large movements, and with the 5/16" firmware...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  11. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    G1 Z5 F5000 ; lift Z by 5mm G28 ; home all axes M565 Z-.68; set the offset for auto-leveling mechanism G29 ; run auto-level G1 Z5 F15000 ; lift Z...
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  12. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    I have one on each z-axis rod, so 2.
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  13. Michael Goodhue
    Post

    Solved Robo3d R1 heated bed going up during print

    To be honest I'm not sure. I got it used other than rod size is there any way to know which version I have? 8mm and 5/16"s are both .31"
    Post by: Michael Goodhue, Mar 26, 2017 in forum: Troubleshooting
  14. Michael Goodhue
    Thread

    Solved Robo3d R1 heated bed going up during print

    Guys, I'm running into a bit of a wierd problem with my Robo3d R1. I have the Robo3d R1 with the 5/16" rods, at least I think they are the...
    Thread by: Michael Goodhue, Mar 26, 2017, 27 replies, in forum: Troubleshooting
Showing results 1 to 14 of 14
Search Again