1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 4
  1. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    Looks like the nozzle dropped while printing first couple layers Or the cube lifted during print Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Dec 3, 2016 in forum: Troubleshooting
  2. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    Now I am seeing this[IMG] big gigantic blob out the side of the nozzle Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Dec 3, 2016 in forum: Troubleshooting
  3. Robert T Loewen
    Post

    Unanswered May have shorted pc fan and x endstop

    [IMG] so damage isn't bad enough to disable it Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Dec 3, 2016 in forum: Troubleshooting
  4. Robert T Loewen
    Post

    Unanswered May have shorted pc fan and x endstop

    Running a test cube now and so far looking good. No smoke or fire Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Dec 3, 2016 in forum: Troubleshooting
  5. Robert T Loewen
    Post

    Unanswered May have shorted pc fan and x endstop

    Don't know if it actually shorted but I think it was damn close Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 29, 2016 in forum: Troubleshooting
  6. Robert T Loewen
    Post

    Unanswered May have shorted pc fan and x endstop

    Well it's all working just haven't tested extrusion Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 29, 2016 in forum: Troubleshooting
  7. Robert T Loewen
    Post

    Unanswered May have shorted pc fan and x endstop

    I sent in a parts request waiting to hear back from that. Did you get the photo of the damage it did? I also put some heat shrink tube on it to...
    Post by: Robert T Loewen, Nov 29, 2016 in forum: Troubleshooting
  8. Robert T Loewen
    Post

    Unanswered May have shorted pc fan and x endstop

    Yup everything is working. Heater might take a couple tries but it works bed works too. Haven't tested the extruder but will soon I even ran the...
    Post by: Robert T Loewen, Nov 29, 2016 in forum: Troubleshooting
  9. Robert T Loewen
    Thread

    Unanswered May have shorted pc fan and x endstop

    Only for a few seconds as I was trying to resolder and test the OC fan and I saw smoke pouring out of the robo3d r1 and cut power and started by...
    Thread by: Robert T Loewen, Nov 29, 2016, 10 replies, in forum: Troubleshooting
  10. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    Got the z tuned and this is what came out from the 20 mm cube. Axis is marked in sharpie[IMG] Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 28, 2016 in forum: Troubleshooting
  11. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    I'm ready for skype. Just waiting on you Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 28, 2016 in forum: Troubleshooting
  12. Robert T Loewen
    Post

    Solved Clogged extruder

    Which model do you have Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
  13. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    So how I read that is nozzle is slightly too high but not enough to cause and not low enough to squish to first layer. Did I get that right? Also...
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
  14. Robert T Loewen
    Post

    Acetone vapor smoothingsmoothing

    First season quote Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Projects
  15. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    I havent leveled y but trying to get z as flat as possible and I can't get a decent measurement Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
  16. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    I have a different one but it's really old Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
  17. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    Here is 1.1 [IMG] Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
  18. Robert T Loewen
    Post

    Acetone vapor smoothingsmoothing

    But Jamie wants big boom Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Projects
  19. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    1.05 or 1.1 Sent from my iPhone using Tapatalk
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
  20. Robert T Loewen
    Post

    Unresolved Would anyone be able to help via skype?

    Yeah they are touching but I think the material is just bubbling after hitting the build plate top does not feel smooth but bottom does Sent...
    Post by: Robert T Loewen, Nov 27, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 70 Next >
Search Again
Page 1 of 4