1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Jesse Koering
    Post

    Solved software update problems

    everything seems to be working!! thank you for all of help! the only problem left is even though i have an sd card in and it says inserted on the...
    Post by: Jesse Koering, Jun 5, 2017 in forum: Troubleshooting
  2. Jesse Koering
    Post

    Solved software update problems

    yes I left that the same, with the exemption of allowing my lcd to work. I replaced the files in the actual folder it self. it compiled...
    Post by: Jesse Koering, Jun 5, 2017 in forum: Troubleshooting
  3. Jesse Koering
    Post

    Solved software update problems

    So I downloaded the files, am I so post to just copy and paste into the file for my printer? or do i replace the same file name in the firmware i...
    Post by: Jesse Koering, Jun 5, 2017 in forum: Troubleshooting
  4. Jesse Koering
    Post

    Solved software update problems

    Sounds good, when I get home tonight I shall. Thanks Sent from my SM-G930V using Tapatalk
    Post by: Jesse Koering, Jun 5, 2017 in forum: Troubleshooting
  5. Jesse Koering
    Post

    Solved software update problems

    exit status 1 expected initializer before 'position' This is the full error above what the line it highlighted.
    Post by: Jesse Koering, Jun 5, 2017 in forum: Troubleshooting
  6. Jesse Koering
    Post

    Solved software update problems

    Thank you for always reponding quick, now I have fixed the filepost part, now it is throwing and error the the line beneith it for -...
    Post by: Jesse Koering, Jun 5, 2017 in forum: Troubleshooting
  7. Jesse Koering
    Thread

    Solved software update problems

    Hello everyone, So, slight re-cap : got a full display xl smart lcd for my printer off a recommendation. I watched several videos on install...
    Thread by: Jesse Koering, Jun 4, 2017, 12 replies, in forum: Troubleshooting
  8. Jesse Koering
    Post

    Answered ABS HELP....Again.

    thank you very much for all the help!!
    Post by: Jesse Koering, Jun 3, 2017 in forum: Troubleshooting
  9. Jesse Koering
    Post

    Answered ABS HELP....Again.

    BEAUTIFUL!! :):):) I am very thankful for you and this community, as there seems to be no shops out herein Roseville! Now one last question....
    Post by: Jesse Koering, Jun 3, 2017 in forum: Troubleshooting
  10. Jesse Koering
    Post

    Answered ABS HELP....Again.

    So I have am still very novice with 3d printing, as I am a diesel tech (not very bright put nicely). Once made of bought I would simply put this...
    Post by: Jesse Koering, Jun 3, 2017 in forum: Troubleshooting
  11. Jesse Koering
    Thread

    Answered ABS HELP....Again.

    Hello All! Long time no talk, I have been taking a break from printing recently but now coming back with more filament and ideas! Now for the...
    Thread by: Jesse Koering, Jun 3, 2017, 6 replies, in forum: Troubleshooting
  12. Jesse Koering
    Post

    ABS not extruding

    sorry i havnt been on for a while, i was out of town, i am looking up difrent ones one line and think i have found some good ones, i just used pla...
    Post by: Jesse Koering, Jan 12, 2017 in forum: United States of America
  13. Jesse Koering
    Post

    ABS not extruding

    lol thank you mark I am gonna be looking up some i saw there was difrent types of nylons is there one thats better?
    Post by: Jesse Koering, Dec 21, 2016 in forum: United States of America
  14. Jesse Koering
    Post

    ABS not extruding

    Is there are types you would sugest or any brands known to be better than others?
    Post by: Jesse Koering, Dec 21, 2016 in forum: United States of America
  15. Jesse Koering
    Post

    ABS not extruding

    I think my wire might be swtiched then, my fans are working oposit of what you said. I am gonna swap the plugs and see if it helps.
    Post by: Jesse Koering, Dec 21, 2016 in forum: United States of America
  16. Jesse Koering
    Post

    ABS not extruding

    The fan defalts are still the same, It seems that it comes on after the first line or two on the z.
    Post by: Jesse Koering, Dec 21, 2016 in forum: United States of America
  17. Jesse Koering
    Post

    ABS not extruding

    I started to look up other slicers and found the one from makerbot looks ok, is there any you may sugest?
    Post by: Jesse Koering, Dec 20, 2016 in forum: United States of America
  18. Jesse Koering
    Post

    ABS not extruding

    I am printing my ABS @ 250 & 80 for the bed. I was told ABS is stronger to build with compared to PLA. I am trying to make a butt stock for an...
    Post by: Jesse Koering, Dec 20, 2016 in forum: United States of America
  19. Jesse Koering
    Thread

    ABS not extruding

    Hello all! I am very new to 3d printing, I just got the ROBO 3d r1+ 2 days ago. I have already put around 8 hrs on it; but I am now encountering...
    Thread by: Jesse Koering, Dec 20, 2016, 18 replies, in forum: United States of America
  20. Jesse Koering
    Post

    Unresolved Abs getting stuck

    :) I will thank you
    Post by: Jesse Koering, Dec 20, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2