1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Barry Steenbergh
    Thread

    Unanswered Smallest gap between printhead and bed

    Hi All, I have a Robo3D Beta and the switch that should tell the printhead to stop prior to hitting the printbed was set too low, I have raised...
    Thread by: Barry Steenbergh, Mar 20, 2017, 1 replies, in forum: Troubleshooting
  2. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Hey Mark, Nope...turns out I lied from the get-go... I have a Robo3d Beta. (In my defense it was sold to me as an R1.. :-/ ) Can you...
    Post by: Barry Steenbergh, Mar 3, 2017 in forum: Troubleshooting
  3. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Ok. You guys seriously rock! That was definitely my issue. The nut wasn't in the crossbar, they were sitting at the bottom of the threaded rod....
    Post by: Barry Steenbergh, Mar 1, 2017 in forum: Troubleshooting
  4. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    The threaded rods turn, but they don't seem to be connected to anything on the printhead. They wobble back and forth.
    Post by: Barry Steenbergh, Feb 27, 2017 in forum: Troubleshooting
  5. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Thanks, Rigmarol. That got it to go through the motions of printing. :) I'm still not sure it is working correctly though... It doesn't seem...
    Post by: Barry Steenbergh, Feb 27, 2017 in forum: Troubleshooting
  6. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Geof, Yeah, a bummer on the non-heated bed, but if I can still do some rudimentary prints with it I will be happy for now. --Barry
    Post by: Barry Steenbergh, Feb 26, 2017 in forum: Troubleshooting
  7. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Mark... Hmmmmm. Well that explains a LOT of my frustrations then... :) I was really just hoping to get my feet wet on printing anyhow with...
    Post by: Barry Steenbergh, Feb 26, 2017 in forum: Troubleshooting
  8. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Hi Geof, Hmmm... Did the beta not have a heated bed? I don't see any wires coming to/from the bed itself... The underbed is pretty...
    Post by: Barry Steenbergh, Feb 26, 2017 in forum: Troubleshooting
  9. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Some printer pics...
    Post by: Barry Steenbergh, Feb 26, 2017 in forum: Troubleshooting
  10. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Hey Everyone, I have nothing connected to my T1 or T2 jumpers on my ramps board (and I dont see anything that would connect). From googling it...
    Post by: Barry Steenbergh, Feb 26, 2017 in forum: Troubleshooting
  11. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Ok. Can anyone point me to the thermistor? :)
    Post by: Barry Steenbergh, Feb 25, 2017 in forum: Troubleshooting
  12. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Hi All, I actually had a few minutes today to troubleshoot further. Replaced my Ramps board with a new one and I have the exact same symptom. :(...
    Post by: Barry Steenbergh, Feb 25, 2017 in forum: Troubleshooting
  13. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Yep R1. Something like this one?...
    Post by: Barry Steenbergh, Feb 8, 2017 in forum: Troubleshooting
  14. Barry Steenbergh
    Post

    Answered Robo3D R1 Bed wont start heating

    Removed Arduino and RAMPS. Separated them and put them back together but didn't seem to help. I get a reading of 0 degrees from the bed but the...
    Post by: Barry Steenbergh, Feb 8, 2017 in forum: Troubleshooting
  15. Barry Steenbergh
    Thread

    Answered Robo3D R1 Bed wont start heating

    Hello folks, Back again with a new question. I have the filament loaded but I can't seem to get my bed to heat so it won't even print a...
    Thread by: Barry Steenbergh, Feb 7, 2017, 37 replies, in forum: Troubleshooting
  16. Barry Steenbergh
    Post

    Solved Robo3D R1 smoke out back and wont power up

    When you said it was a tight fit you were NOT kidding. A little sweat, a lot of blood, and the new power supply was installed. And... IT...
    Post by: Barry Steenbergh, Feb 7, 2017 in forum: Troubleshooting
  17. Barry Steenbergh
    Post

    Solved Robo3D R1 smoke out back and wont power up

    Answering my own question in case it helps anyone else. Appears that it just slides out... [MEDIA]
    Post by: Barry Steenbergh, Jan 31, 2017 in forum: Troubleshooting
  18. Barry Steenbergh
    Post

    Solved Robo3D R1 smoke out back and wont power up

    In anticipation of the power supply arriving tonight...can anyone give me some pointers on how to remove the old one? I don't really see any...
    Post by: Barry Steenbergh, Jan 31, 2017 in forum: Troubleshooting
  19. Barry Steenbergh
    Post

    Solved Robo3D R1 smoke out back and wont power up

    Hey all, connected the arduino to my pc and I see it (arduino mega 2560). I'm still really suspicious of the power supply tho. The Magic white...
    Post by: Barry Steenbergh, Jan 29, 2017 in forum: Troubleshooting
  20. Barry Steenbergh
    Post

    Solved Robo3D R1 smoke out back and wont power up

    Thanks Mark! I will try that tonight.
    Post by: Barry Steenbergh, Jan 28, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2