1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Kay Liu
    Thread

    Partial Answer After printing, right and left side not at same level

    Hi guys, I have a R1+. Recently when I try to print something tall, the printer always end up like left side at a very high level, but right side...
    Thread by: Kay Liu, Oct 24, 2017, 1 replies, in forum: Troubleshooting
  2. Kay Liu
    Post

    Solved Auto bed leveling adjustment

    I tried that, it works! Thanks!
    Post by: Kay Liu, Jun 20, 2017 in forum: Troubleshooting
  3. Kay Liu
    Post

    Solved Auto bed leveling adjustment

    copied from start gcode G28 G92 E0 ; M565 Z-1.2; G1 Z5 F5000 ; G29 ; so z offset is 1.2
    Post by: Kay Liu, Jun 16, 2017 in forum: Troubleshooting
  4. Kay Liu
    Post

    Solved Auto bed leveling adjustment

    So this is the first layer looks like...
    Post by: Kay Liu, Jun 16, 2017 in forum: Troubleshooting
  5. Kay Liu
    Thread

    Solved Auto bed leveling adjustment

    Hello, I have a R1+, it has been working very well, the only problem now is that the bed itself seems not at the same level for each corner. I...
    Thread by: Kay Liu, Jun 16, 2017, 6 replies, in forum: Troubleshooting
  6. Kay Liu
    Post

    Solved Gap between layers Please help!!

    Hey guys, thanks for all your replies This was solved by one of the technicians during ROBO tech appt. It was combined with too tight spring...
    Post by: Kay Liu, Jun 15, 2017 in forum: Troubleshooting
  7. Kay Liu
    Post

    Solved Gap between layers Please help!!

    I tried to adjust z off-set to make enough space between the hotend and the bed, but still not work well. :'(
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  8. Kay Liu
    Post

    Solved Gap between layers Please help!!

    I tried 1.2 of extrusion multipliers. I would say it's worse. :(
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  9. Kay Liu
    Post

    Solved Gap between layers Please help!!

    it says 1. I attached the screenshot
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  10. Kay Liu
    Post

    Solved Gap between layers Please help!!

    it's matter control 1.5
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  11. Kay Liu
    Post

    Solved Gap between layers Please help!!

    hotend temperature is 210 as default setting
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  12. Kay Liu
    Post

    Solved Gap between layers Please help!!

    I tried again, this is the first layer looks like
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  13. Kay Liu
    Post

    Solved Gap between layers Please help!!

    Hey guys, I tried seasoning the hotend, but still very bad printing quality, or say even worse. Any other possibilities??
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  14. Kay Liu
    Post

    Solved Gap between layers Please help!!

    Thanks for your reply! I read the the link you shared, one thing I still not quite sure is that is R1 plus hotend all metal?
    Post by: Kay Liu, Jun 12, 2017 in forum: Troubleshooting
  15. Kay Liu
    Thread

    Solved Gap between layers Please help!!

    Hello, we bought a R1 plus in March. It has been working so well since last month. Last week we tried to print out a prototype model, but every...
    Thread by: Kay Liu, Jun 11, 2017, 27 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again