1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Michael hineman
    Post

    Camera Not working

    So can you not do manual updates? Like the issue I had with RoboLCD?
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  2. Michael hineman
    Post

    Camera Not working

    Yes It does not do it internet explorer. I am using Firefox.
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  3. Michael hineman
    Post

    Lost main board connection?

    No I have not gotten a chance to speak with anyone from support. I will call tomorrow for sure. I'd say no one home on the holidays.
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  4. Michael hineman
    Post

    Lost main board connection?

    Well before it quit completely the bed heat up really fast. It was at temperature shortly after the leveling sequence.
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  5. Michael hineman
    Post

    Lost main board connection?

    Hey since I soldered the pins. I cant get bed temperature 90 or above. Is this due to soldering of the pins 0r the pins being damaged? It also is...
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  6. Michael hineman
    Post

    Camera Not working

    Is this Normal? Turn Camera Off, Turn Camera Off, Turn Camera Off.............. [ATTACH]
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  7. Michael hineman
    Post

    Camera Not working

    Yes, I am an idiot. That was it. I had it backwards. Working now.
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  8. Michael hineman
    Post

    Camera Not working

    I know I re-seated the camera ribbon cable while troubleshooting. I hope I did not put it in backwards. Would this damage the camera?
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  9. Michael hineman
    Post

    Camera Not working

    [ATTACH]
    Post by: Michael hineman, Jan 1, 2018 in forum: Troubleshooting
  10. Michael hineman
    Post

    Camera Not working

    no nothing there.
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  11. Michael hineman
    Post

    Camera Not working

    OK did that still no camera....:( could it be octoprint? Is there another way to test? I saw someone say something about camera in Cura? Not sure...
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  12. Michael hineman
    Post

    Camera Not working

    What is the current version of OCTOPRINT?
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  13. Michael hineman
    Post

    Camera Not working

    I re-flashed with this. https://drive.google.com/drive/folders/0B_cJvRC01dTYTFF5V0wzWF9oMFU?usp=sharing Stupid question,,,,I am familiar with...
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  14. Michael hineman
    Thread

    Camera Not working

    OK. I have got printer printing and before re-flashing SD card with working image had no problem displaying camera. Now the camera will not...
    Thread by: Michael hineman, Dec 31, 2017, 29 replies, in forum: Troubleshooting
  15. Michael hineman
    Post

    Lost main board connection?

    I soldered the two pins in place and I am printing again. I hope to hear back from support soon. I really appreciate this community and the help...
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  16. Michael hineman
    Post

    Lost main board connection?

    is there anything I can do til I get a new pogo pin board or r2 bed. It would be nice to print something today. Is it possible to replace the springs?
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  17. Michael hineman
    Post

    Lost main board connection?

    You were all over it......I appreciate your help. Do you work for Robo? you should if not.
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  18. Michael hineman
    Post

    Lost main board connection?

    OK! I found this issue. I downloaded the SD card image located here...
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  19. Michael hineman
    Post

    Lost main board connection?

    Unfortunately I guess with the holidays that leaves me kinda high and dry. The only thing I got from support was to check the cable connections. I...
    Post by: Michael hineman, Dec 31, 2017 in forum: Troubleshooting
  20. Michael hineman
    Post

    Lost main board connection?

    I still am having these issues. They are more often now, every time I try and print. I happens regardless if printing from memory or USB. I have...
    Post by: Michael hineman, Dec 29, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2